Q-Acoustics

The model uses a 25 mm fabric RF emitter with ferromagnetic coolant, a hybrid of ring and dome tweeters (such a speaker can often be found in High-End speakers), providing extremely low distortion and wide dispersion.

A bookshelf 2-way speaker system with a rear bass reflex and two speakers, the size of which is 100 mm and 22 mm. The model is ideally suited for use in conjunction with home theaters and stereo equipment.

The model uses a 22mm radiator for high frequency reproduction and a 120mm bass drive for low frequencies. This bookshelf speaker is light in weight, boasts a sensitivity of 87 dB and a nominal resistance of 6 ohms.

Bookshelf two-lane speakers. Precision speakers with diameters of 125 mm (5 inches) and 22 mm (0.9 inches). P2P (point-to-point) mounting. Increased internal volume.

The new 3000c series features the C3 midrange speaker design with a continuous curved cone. The C3 speaker, used throughout the model range, is designed to eliminate the disadvantages of traditional speakers. Introduced for the first time in the Q Acoustics 5000 series speaker range, the C3 speaker combines the advantages of a traditional rectilinear conical housing for low-frequency reproduction with an expandable housing for medium and high frequency control.

The acoustics remained quite compact: only 200x325x329 mm. But a woofer from the 3050i floor—mounted speakers got into this rounded case - a 6.5-inch speaker, which, however, was optimized for small-volume operation by updating the magnetic system and winding copper-plated aluminum wire onto coils. As a result, these babies can bass as much as 46 Hz.

The M20 stereo pair is made according to the classic master-slave principle, when all the electronics are concentrated in one of the speakers. This is an amplifier that outputs 65 watts per channel, and a DSP module with the ability to adjust the sound depending on the location of the speakers: in a corner, against a wall, or freely. A 22mm tweeter and a 125mm woofer are responsible for the sound in each speaker. The audio signal of the Q Acoustics M20 is received via Bluetooth 5.0.

The Q Acoustics Q5010 is a bookshelf speaker that stands between the 3000i models and the older Concept series. Many technologies of Q Acoustics 5000 cabinets and drivers are borrowed from the latter. In particular, this is the design of the C3 Continuous Curved Cone woofers/midrange speakers, about which Q Acoustics stated that the C3 "will form a technological platform for many years to come."

Q Acoustics 5020 is a bookshelf speaker with an innovative design of midrange and woofer drivers. The C3 Continuous Curved Cone design in midrange/woofer provides smoother integration of treble with tweeter and superior bass dynamics.

The Concept 30 used specially designed radiators: 5-inch midrange/woofer speakers with enlarged 30.5 mm coils and 0.9-inch tweeters mounted on 3 mm thick aluminum plates. The tweeter is placed in a sealed volume and is completely isolated from the body by means of a "floating" suspension. The midrange/woofer sound coil is 30.5 mm in diameter.

This is not the tiniest model: each column weighs about 15 kg, which is quite a lot for shelves. On the front panel there is a 6.5-inch midbass speaker and an enlarged 1.1-inch tweeter. At low frequencies, the bass is assisted by a bass reflex mounted on the back panel.

Q-Acoustics Active 200 is a Hi-Fi class wireless bookshelf speaker. Amplifier modules operating in Class D are used, and band-pass amplification with active crossover based on DSP is implemented. The Q Active 200 shelf model has six amplifiers with a total power of 280 watts.

The Q Acoustics 5050 is an floorstanding 2–way loudspeaker, it is the flagship model of the "5000" series from Q Acoustics. The 5050 model, in addition to the standard tweeter for its series, is equipped with two 6-inch bass speakers, the largest midrange/woofer speakers in the entire series, specially designed for this speaker.

The model 3050 I has a two-band configuration with a bass reflex and is equipped with a pair of woofers with a diameter of 165 mm and a 22 mm tweeter. The bass reflex hole on the back panel can be closed with a foam plug to adjust the bass sound. The speakers have beautiful chrome frames, and the exterior finish of the speakers can be Arctic White, Carbon Black, Graphite Grey or English Walnut (all options are matte).

The Q Acoustics 3050c has a strikingly curved body that uses Q Acoustics' patented P2P mounting technology. There are also Helmholtz pressure equalization tubes. There are no visible connections or fasteners, and internal spacers connect the parts of the body that are most susceptible to resonances.

The active floorstanding loudspeakers are equipped with Class D amplifiers with a power of 100 watts per channel. The built-in Bluetooth 5.0 module uses the aptX HD and aptX Low Latency codecs, in addition, there are analog RCA and 3.5mm inputs, as well as a digital optical input. The streaming module and network interface, as well as the HDMI input are not provided.

The Q Acoustics 5040 tweeter is equipped with a silk dome that is connected to a concave suspension, which improves off-axis directional characteristics. The tweeter is located between two accounts/woofers, i.e. in the D'apolito configuration, which also contributes to optimal off-axis characteristics of the reproduced sound.

The Concept 50, a derivative of the flagship Concept 500, uses HP technology. Thanks to HP (Helmholtz Pressure Equalizer) technology, distortion is minimized. Large speaker housings can create pressure in certain areas, causing resonance and distortion of the housing.

Q Acoustics Active 400 is a powerful high–resolution wireless stereo system with support for Bluetooth, AirPlay 2, Chromecast, Roon, Amazon Music, Apple Music, Deezer, Qobuz, Spotify, Tidal, HDMI ARC, providing uncompromising Hi-Fi sound. The system consists of two active outdoor speakers and a wireless hub with additional connectors.

The model is equipped with two newly developed 16.5cm midrange/bass speakers with reduced distortion and a new 28 mm tweeter with a soft dome and wide frame. The stylish speakers of the Concept 500 have been rebuilt from scratch and, in particular, are equipped with enclosures, the design of which has made significant changes to improve the sound quality.

This is the largest and most powerful Q B12 subwoofer from the English company, which will complement the Q Acoustics 3000i and Concept 5.1 home theater speaker lines. The subwoofer has also received the appropriate finish — in vinyl or lacquer.

The 3060s subwoofer is capable of delivering all the nuances of an acoustic double bass or the roar of an explosion in a movie when using a powerful 150-watt amplifier paired with a high-quality 200 mm speaker.

The cases of the Q Acoustics Q Sub subwoofers are made of MDF panels with a thickness of 18 mm, while the thickness of the front wall of the case is as much as 36 mm. The younger model, the Q Acoustics Sub 80, weighs 15 kilograms, is equipped with a 200-watt amplifier and reproduces bass starting at 36 Hz.

The Q Acoustics Sub 100 weighs 16.7 kg, has a power of 250 watts and a starting frequency of 32 Hz. The built-in amplifiers are complemented by digital signal processing (DSP) technology to optimally adjust the subwoofer to the acoustic features of the listening room.

The largest model in the series is the Q Sub 120. It weighs 22.5 kg, develops up to 300 watts and operates at a frequency of 28 Hz.