Hifiverse

Floorstanding loudspeakers — JM Reynaud ORFEO JUBILE

Description, images, technical data and specifications

JM Reynaud ORFEO JUBILE
Image source - (c) JM Reynaud

The ORFEO JUBILE is a floorstanding loudspeaker in the Jubile series from the French manufacturer Jean-Marie Reynaud (JMR). According to JMR it is not an upgrade of the Orfeo Supreme V2 but a completely new development. The cabinet is tuned lower still and has a wide radius on its rear horizontal edge. Price is EUR 11,500 per pair in Cherry Stained Anigre veneer, Black Satin, Pearly White or Pearly Anthracite Grey.

Key specs that matter

It is a 2.5-way design with an AST-type aerostriction tweeter and two 180 mm bass-midrange drivers, which work in tandem and in phase below 400 Hz. Frequency response is 32 Hz - 25 kHz (30 Hz at -6 dB). Sensitivity is 91 dB/W/m (2.83 V) and impedance is 4 ohms (3.8 ohms minimum). Power handling is 90 - 300 W, with a 400 W peak. Crossover slopes are 12/12/6 dB per octave, and the terminals accept mono wiring or bi-wiring. Dimensions are H 116, W 23.5, D 33 cm. Weight is 40 kg.

Engineering and use context

The tweeter has a pleated diaphragm 25 mm wide and 60 mm high with an aluminium film coating. It works as a dipole, so a small sealed chamber is placed behind it. Its housing is a turned solid-wood piece, decoupled from the top of the cabinet by a bitumen gasket.

Both 180 mm drivers are new and were developed with a German company that works only on OEM products. Their cone is made of 7 layers of carbon fibre and PEEK and has a plasma treatment on the outer surface. A 37 mm voice coil on a ventilated fibreglass former works with a double 100 mm ferrite magnet, and there is a pure copper ring in the air gap. The basket is aluminium and the surrounds are NBR rubber.

JMR builds the crossover by hand, without a printed circuit board, in two separate cells to avoid intermodulation. It uses silver solder, silver-armature capacitors terminated with JMR's HP1132 cable, pure copper-strip chokes wound on solid-wood formers and sealed in wax, and resistors shielded by a grounded copper tube. Components are measured and sorted in pairs to a 1% tolerance.

Bass loading remains a triangular line tuned in 1/4 wave, leading to a front vent at the foot of the speaker. A ring of open-cell foam sits behind the cones, and large areas of the cabinet walls are lined with bitumen and viscoelastic compound. The cabinet rests on a plinth decoupled by a viscoelastic gasket, on adjustable spikes with spike cups.

Pairing

This is a sensitive speaker, but it is also a 4 ohm load with a stated lower power limit. A solid-state amplifier that is stable into 4 ohms is the natural match, and the bi-wire terminals also allow passive bi-amplification.

Alternatives

The ABSCISSE JUBILE is the smaller floorstanding loudspeaker in the Jubile range, with two 14 cm drivers, a 115 cm cabinet, a weight of 30 kg and 89 dB sensitivity.

Specifications

  • Model name

    ORFEO JUBILE

  • Frequency Response low +/- 3dB (Hz)

    32

  • Frequency Response high +/- 3dB (Hz)

    25 000

  • Sensitivity (dB at 1 W/1m)

    91

  • Impedance (Ohms)

    4

  • Power amplifier requirements (W)

    90 - 300

  • Has internal amplification

    N/A

  • Internal amplification power (W)

    N/A

  • Size (sm)

    116 × 23.5 × 33

  • Weight (kg)

    40

  • Official link

More components