Hifiverse

Floorstanding loudspeakers - JBL 4367

Description, images, technical data and specifications

JBL 4367
Image source - (c) JBL

The 4367 is a two-way floorstanding Studio Monitor from JBL, part of the JBL Synthesis range from Northridge, California. It replaces the 4365, first produced in 2010 with a 1501FE-8 woofer, a 476Mg high-frequency compression driver and an 045Ti-1 ultra-high-frequency compression driver. With a single D2430K in place of both horn drivers, the 4367 returns to the two-way layout JBL used in the 1950s and 1960s and keeps the exposed horn and blue baffle of the Studio Monitor series. JBL intends it for 2-channel systems or as LCR loudspeakers in a JBL Synthesis home theater. Finishes are Walnut and Black Walnut wood veneer.

Key specs that matter

Enclosure type is bass reflex via dual front-firing ports. Its 380 mm 2216Nd-1 Differential Drive woofer has an Aquaplas-treated Pure Pulp cone, dual 76 mm voice coils, a neodymium motor structure and a cast aluminium frame. A 75 mm D2430K compression driver with dual diaphragms, dual voice coils and dual neodymium motor structures operates above the 700 Hz crossover. Frequency response is 30 Hz - 40 kHz (-6 dB), and bass response is 26 Hz (-10 dB). Sensitivity is 94 dB (2.83 V/1 m), and nominal impedance is 6 ohms. Horn coverage is 110 degrees horizontal by 50 degrees vertical. Each speaker measures 941 x 560 x 425 mm (H x W x D) and weighs 54 kg.

Engineering and use context

The Differential Drive motor is a dual-voice-coil, dual-gap system with shorting rings, a flux-stabilising ring, saturation tips and a heat-conducting ring. For the 2216Nd-1 JBL lists a 28 Hz free-air resonance and about 7 mm of peak-to-peak linear excursion. Inside the D2430K, two annular polymer diaphragms give the radiating area of a single 75 mm diaphragm at a lower mass-to-motor force ratio, with 0.95 g total moving mass. High and ultra-high frequencies come from this single coincident source. Its HDI waveguide horn is made of BMC (bulk moulding compound).

Cabinet walls are 25 mm MDF with a further 16 mm surface baffle below the horn, and two braces connect all vertical panels. Both 102 mm ports are dual-flared. The crossover network uses two separate boards, one for each transducer, with air-core inductors and polypropylene foil capacitors. A diode charging circuit driven by the applied signal puts a DC bias on the capacitors. Front-panel HF and UHF controls adjust from -1 dB to +1 dB in 0.5 dB steps, over 600 Hz - 9 kHz and from 4 kHz to beyond 20 kHz respectively.

Pairing

JBL suggests an amplifier power range of 25 - 300 W. Dual gold-plated five-way binding posts allow bi-wiring or bi-amplification, and jumper wires are supplied for a single amplifier channel.

Alternatives

The JBL Project Everest DD67000 is a larger three-way floorstanding model with two 380 mm woofers and beryllium compression drivers.

Specifications

  • Model name

    4367

  • Frequency Response low +/- 3dB (Hz)

    30

  • Frequency Response high +/- 3dB (Hz)

    40 000

  • Sensitivity (dB at 1 W/1m)

    94

  • Impedance (Ohms)

    6

  • Power amplifier requirements (W)

    <300

  • Has internal amplification

    N/A

  • Internal amplification power (W)

    N/A

  • Size (sm)

    94.1 x 56.0 x 42.5

  • Weight (kg)

    54

  • Official link

More components