Hifiverse

Phonovorstufen - Allnic Audio H-6500

Beschreibung, Bilder, technische Daten und Spezifikationen

Allnic Audio H-6500
Bildquelle - (c) Allnic Audio

The Allnic Audio H-6500 is a tube phono preamplifier with a separate power supply, and it is the third of four models in the Allnic phono range, above the H-5500 and below the H-7000 and the H-8000 DHT. Designed in South Korea by Kang Su Park's company, it was priced at USD 9,900 in the US and EUR 9,500 in Europe. Its moving-coil step-up transformers share their design with those inside the H-7000.

Key specs that matter

Each Allnic H-6500 offers two MM and two MC input pairs plus a single output pair, every one of them RCA, and two screw terminals accept turntable ground wires. Voltage gain is 40 dB for MM and 62, 66, 68 or 72 dB for MC. MM inputs present 47 kohm, MC loading reaches up to 117 ohm, and the output impedance is 430 ohm. RIAA deviation stays within 0.3 dB from 20 Hz to 20 kHz, THD is below 0.17% at 1 kHz and 1 V output, with a CCIR-weighted S/N figure of -86 dB. Without clipping the MM stage accepts 30 mV at 20 Hz, 100 mV at 100 Hz, 240 mV at 1 kHz and 280 mV at 10 kHz. The amplifier unit is 430 x 335 x 170 mm and weighs 8 kg, the supply 170 x 275 x 118 mm and 8.1 kg.

Engineering and use context

Eight 5842 triodes provide the amplification, four per channel, a tube type Allnic compares to the WE 417A. RIAA correction is handled by an LCR filter, and the MC inputs pass through built-in Permalloy-core step-up transformers with four winding ratios. Impedance and gain are set with turret knobs on the chassis, and the gain markings show what the transformers add rather than the total figure. The regulated supply relies on two 7233 tubes as series regulators and two 5654 tubes for automatic voltage regulation. The owner installs the 5AR4 rectifier tube in the external box before first use, and an umbilical cable links the two chassis. Permalloy output transformers are used at the output, and analog meters on the front panel monitor tube condition. All tubes supplied are NOS types.

Pairing

With single-ended outputs only, the H-6500 must feed RCA line inputs on a preamp or integrated amplifier. Because every cartridge type gets a doubled set of sockets, an owner with a second arm or deck can leave both connected, mixing an MM pickup with an MC one if needed. The low MC loading ceiling fits moving-coil cartridges with low internal impedance.

Alternatives

The Allnic Audio H-7000V sits higher in the phono line, adding an XLR output, a head-amplifier input and selectable equalisation curves for records cut before the RIAA standard.

Spezifikationen

  • Modellbezeichnung

    H-6500

  • Eingänge (symmetrisch)

    N/A

  • Eingänge (unsymmetrisch)

    4

  • MC-Eingangsimpedanz (stromgekoppelt) (Ω)

    N/A

  • MM/MC-Eingangsimpedanz (spannungsgekoppelt) (Ω)

    MC up to 117 (see “Impedance” in “Initial Set-Up”) MM 47 000

  • Ausgangsimpedanz (Ω)

    430

  • Verstärkung (dB)

    40 (MM), 66 (MC)

  • Genauigkeit der Wiedergabe-Entzerrungskurven (dB)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    20

  • Obere Grenzfrequenz +/- 3dB (Hz)

    20 000

  • Klirrfaktor + Rauschen (%)

    <0.17

  • Abmessungen (mm)

    430 x 335 x 170 (Phonostage) + 170 x 275 x 118 (Power supply)

  • Gewicht (kg)

    8 (Phonostage) + 8.1 (Power supply)

  • Offizieller Link