Hifiverse

CD / SACD players and transports - Cyrus Audio CDi

Description, images, technical data and specifications

Cyrus Audio CDi
Image source - (c) Cyrus Audio

The CDi is the integrated CD player of the Classic series from Cyrus Audio, the British maker of half-width electronics. Disc drive, digital to analogue converter and analogue output stage share one die-cast chassis. It uses the Cyrus Servo Evolution CD engine, introduced in 2008, and the same 32-bit DAC as the DAC XP Signature. The US list price was USD 2,100, and Cyrus gives a two-year warranty.

Key specs that matter

Disc compatibility is CD Audio and CD-R. Analogue output level is 2.1 V rms, and frequency response is 20 Hz - 20 kHz (±0.25 dB). Channel separation is better than 110 dB at 1 kHz and 90 dB at 20 kHz. Signal-to-noise ratio is better than 106 dBA (silent track), and THD is 0.003% at -10 dB. On the digital side Cyrus specifies 500 mV peak-to-peak into 75 ohms for the coaxial output, sample rate accuracy of 44.1 kHz ±50 ppm and clock jitter below 75 ps. Power consumption is 12 W. Dimensions are 215 x 75 x 365 mm (W x H x D), and weight is 3.6 kg.

Engineering and use context

Cyrus controls the whole electro-mechanical servo system of the drive. In a conventional mechanism the servo makes small, rapid side-to-side movements to re-read misread data, and Cyrus states that this servo noise raises the noise floor. Servo Evolution aims to extract the data correctly on the first pass, and that depends on joint design and calibration of hardware and software. Discs load through a front slot. Cyrus describes this slot loader as a quiet, low-contact mechanism that replaces the tray and clears the front panel.

Its circuit is laid out in two discrete sections. With a PSX-R or PSX-R2 connected, the internal power feeds are split two ways, and the external supply powers the sensitive circuit sections. This isolates the DAC section and separates control circuits from the analogue stages, lowering mains-borne noise and power supply ripple. Inside the inverted die-cast chassis the sensitive audio circuits are hung from the chassis, which is designed as an electronically shielded enclosure.

The rear panel has two pairs of RCA analogue outputs (OUT 1 and OUT 2), optical and coaxial digital outputs, MC-BUS sockets and the PSX-R connection. An iR14 remote and two phono leads for MC-BUS are supplied.

Pairing

The analogue outputs connect to a CD or AUX line input, never to a phono input. For an external D/A converter Cyrus recommends the coaxial digital output. MC-BUS gives full system remote control with a Cyrus amplifier. The matching power supply upgrade is the PSX-R2.

Alternatives

The CDi-XR is the higher Cyrus integrated CD player, with a second-generation QXR DAC and a PSU-XR port.

Specifications

  • Model name

    CDi

  • Transport

    Yes

  • Player

    Yes

  • SACD support

    N/A

  • Engine

    N/A

  • Frequency response low +/- 3dB (for CD) (Hz)

    N/A

  • Frequency response high +/- 3dB (for CD) (Hz)

    N/A

  • Frequency response low +/- 3dB (for SACD) (Hz)

    N/A

  • Frequency response high +/- 3dB (for SACD) (Hz)

    N/A

  • Gain (dBu)

    N/A

  • Output Level (balanced) (V)

    N/A

  • Output Level (single-ended) (V)

    N/A

  • Input Impedance (balanced) (Ω)

    N/A

  • Input Impedance (single-ended) (Ω)

    N/A

  • Output Impedance (balanced) (Ω)

    N/A

  • Output Impedance (single-ended) (Ω)

    N/A

  • Dynamic range (for CD) (dB)

    N/A

  • Dynamic range (for SACD) (dB)

    N/A

  • Signal to Noise Ratio (for CD) (dB)

    N/A

  • Signal to Noise Ratio (for SACD) (dB)

    N/A

  • Total Harmonic Distortion + Noise (for CD) (%)

    N/A

  • Total Harmonic Distortion + Noise (for SACD) (%)

    N/A

  • Dimensions (mm)

    N/A

  • Weight (kg)

    N/A

  • Official link

More components