Hifiverse

Floorstanding loudspeakers — German Physiks Carbon MK IV

Description, images, technical data and specifications

German Physiks Carbon MK IV
Image source - (c) German Physiks

The Carbon Mk IV is an omnidirectional floorstanding loudspeaker in the Reference Series of German Physiks, built by DDD Manufactur in Maintal, Germany. It is a luxury version of the Borderland Mk IV and is available only in a carbon fibre finish. When the Carbon Mk I appeared, it differed technically from the Borderland Mk I, which is why it received its own name. Today the finish is the only difference. The Borderland itself was introduced in 1992 and is still the company's most popular loudspeaker.

Key specs that matter

This is a 2-way loudspeaker with 360° surround radiation, using one carbon fibre DDD driver and one 305 mm (12 in) woofer. Crossover frequency is 190 Hz, with slopes of 12 dB/octave electronic and 18 dB/octave acoustic for both sections. German Physiks specifies 28 Hz - 24 kHz, a sensitivity of 86.1 dB (1 W/1 m) and an impedance of 4 ohms. Power handling is 300 W nominal and 600 W short term. Input connectors are two sets of WBT nextgen binding posts. Each speaker measures 404 x 1,229 x 404 mm (W x H x D) and weighs 54 kg.

Engineering and use context

Its DDD driver covers 190 Hz - 24 kHz, and the woofer adds only the lowest octaves. The cone is 0.15 mm carbon fibre sheet and is always mounted vertically, so sound is radiated sideways through 360 degrees. Up to about 200 Hz it moves as a piston. Above that, bending waves take over progressively until, at about 800 Hz, all energy is radiated by bending waves, and from the dipole frequency of about 4 kHz the cone works in modal radiation. Moving mass is under 3 g. Behind the cone is a ferrite magnet of German Physiks' own design with an underhung voice coil and approximately 1.2 Tesla in the gap. The coil is wound from flat wire on edge and completely enclosed in the magnet structure, which acts as a heat sink.

At the bottom of the cabinet the woofer, of the same type as in the Loreley Mk III, faces downward in a sealed enclosure. A Helmholtz resonator - a small cavity at the top of the cabinet linked to the bass enclosure by a small opening - is used to avoid unevenness in the bass response. The cabinet has an octagonal cross-section with smaller, stiffer panels and internal bracing. Hawaphon damping, a polymer sheet with cells of fine steel shot, is applied to each panel and is quoted at more than 50 dB attenuation of structure-borne sound. A lining of high-density felt damps the air inside. Each speaker is measured, burnt in for at least 12 hours and measured again.

Pairing

An amplifier of at least 160 W into 4 ohms is required. Separate inputs for the woofer and DDD crossover sections allow single or bi-wire connection.

Alternatives

The Borderland Mk IV is the same loudspeaker in high-polish polyester and veneer finishes.

Specifications

  • Model name

    Carbon MK IV

  • Frequency Response low +/- 3dB (Hz)

    28

  • Frequency Response high +/- 3dB (Hz)

    24 000

  • Sensitivity (dB at 1 W/1m)

    86.1

  • Impedance (Ohms)

    4

  • Power amplifier requirements (W)

    4 - 160

  • Has internal amplification

    N/A

  • Internal amplification power (W)

    N/A

  • Size (sm)

    40.4 x 122.9 x 40.4

  • Weight (kg)

    54

  • Official link

More components