Hifiverse

Power amplifiers mono - Emotiva XPA-1 Gen3

Description, images, technical data and specifications

Emotiva XPA-1 Gen3
Image source - (c) Emotiva

XPA-1 Gen3 is a monoblock power amplifier from Emotiva, built on the XPA Gen3 platform with one high-powered single-channel module. Emotiva designs, assembles and tests it at its plant in Franklin, Tennessee, and covers it with a five-year warranty. A pair is intended for a stereo or 2.1 music system, and three can drive the front left, centre and right channels of a 5.1 or 7.1 home theatre.

Key specs that matter

Rated output is 300 W RMS into 8 ohms (20 Hz - 20 kHz, THD <0.1%) and 600 W RMS into 4 ohms (THD <0.2%), with 4 ohms as the minimum load. Broadband frequency response is 5 Hz - 80 kHz (+0/-2 dB). THD+N is below 0.005% at 100 W, 1 kHz into 8 ohms. Signal-to-noise ratio is above 117 dB referenced to rated power and above 91 dB referenced to 1 W (unbalanced, A-weighted). Damping factor exceeds 500 into 8 ohms. Gain is 29 dB, and input sensitivity is 1.71 V for rated power into 8 ohms. Input impedance is 33 kohms balanced and 23.5 kohms unbalanced. Mains input is 100 - 250 V AC, 50/60 Hz, detected automatically, and maximum consumption with continuous full-power test tones is 1000 W. Dimensions are 432 x 203 x 483 mm (W x H x D, with feet), and weight is 15.2 kg.

Engineering and use context

The amplifier module is independent and fully discrete, with a dual differential, high current, short signal path Class A/B circuit. Power comes from a switched mode power supply using what Emotiva calls an Optimized Soft-Switch Class H power supply topology. Emotiva states that the SMPS gives improved efficiency and reliability and lower overall weight than a traditional linear supply. Construction of the Gen3 platform is fully modular.

Protection covers excessive operating temperature, shorted speaker connections, ground faults and other common fault conditions, and a resettable circuit breaker on the rear panel protects against AC line faults. On the front, a standby push button has a halo ring that changes colour between standby and on, and a blue status LED turns red on a fault. The rear panel carries RCA and XLR inputs, independently selectable, gold plated 5-way binding posts and a trigger input (5 - 12 V AC or DC) with a 12 V DC trigger output for loads up to 120 mA. Its heavy steel 4RU chassis has a milled aluminium faceplate.

Pairing

A preamplifier or AV processor with balanced or unbalanced outputs is required. Loudspeakers of 4 ohms or higher match it. The trigger connections allow switch-on together with a trigger-equipped preamplifier.

Alternatives

The XPA-DR1 is Emotiva's other mono power amplifier.

Specifications

  • Model name

    XPA-1 Gen3

  • Input sensitivity (mV)

    1710

  • Input impedance (balanced) (Ω)

    33 000

  • Input impedance (single-ended) (Ω)

    23 500

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    300

  • Output power (4Ω) (W)

    600

  • Gain (dBu)

    29

  • Frequency response low +/- 3dB (Hz)

    5

  • Frequency response high +/- 3dB (Hz)

    80 000

  • Signal to Noise Ratio (dB)

    >117

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    < 0.005

  • Max power consumption (W)

    100

  • Damping factor

    > 500

  • Dimensions (mm)

    432 × 203 × 483

  • Weight (kg)

    15,2

  • Official link

More components