Hifiverse

Power amplifiers mono - Emotiva BasX A1

Description, images, technical data and specifications

Emotiva BasX A1
Image source - (c) Emotiva

The BasX A1 is a monoblock power amplifier from Nashville-based Emotiva and part of its BasX series. Each A1 is one channel with its own heavy-duty power supply in its own chassis, so a stereo system uses a pair. Emotiva also proposes it for the most critical channels of a multichannel system, such as the centre channel. The price was USD 569 per unit, and Emotiva now lists the model as discontinued.

Key specs that matter

Power output is 200 W RMS into 8 ohms (20 Hz - 20 kHz, THD below 0.05%) and 325 W RMS into 4 ohms (1 kHz, THD below 0.1%). Power bandwidth is 20 Hz - 20 kHz (±0.07 dB) at rated power into 4 - 8 ohms, and broadband frequency response is 5 Hz - 80 kHz (+0/-1.8 dB). THD+N is below 0.02% (A-weighted, ref. rated power). Signal-to-noise ratio is above 112 dB (8 ohms, ref. rated power, A-weighted). Input sensitivity is 1.6 V for rated power into 8 ohms, gain is 29 dB and input impedance is 27 kohms. Damping factor is above 500 into 8 ohms. Minimum recommended load is 4 ohms, one 4 ohm speaker or two 8 ohm speakers in parallel. Dimensions are 432 x 102 x 394 mm (W x H x D) without connectors, and weight is 10 kg.

Engineering and use context

Emotiva combines a heavy-duty linear power supply with a high-current, short-signal-path Class A/B output stage. It uses an oversized toroidal power transformer, and microprocessor-controlled circuitry monitors operation and protection. Protection covers excessive temperature, shorted speaker connections and ground faults. Inside, double-sided FR4 circuit boards with plated-through holes reduce point-to-point wiring. A heavy steel chassis carries a milled aluminium faceplate.

On the rear panel are a single unbalanced RCA input and 5-way binding posts for bare wire, lugs or banana plugs. Its trigger input accepts 5 - 12 V AC or DC at under 10 mA, and the trigger output supplies 12 V DC into loads up to 120 mA. Mains voltage is 115 or 230 V at 50/60 Hz, detected automatically. Front-panel controls are a standby push button, a blue status LED that turns red on a fault and an amber standby LED. A rear rocker switch disconnects AC power, and a second switch disables the status LED. Warranty is three years.

Pairing

A preamplifier or AV processor with unbalanced RCA outputs is required. Loudspeakers of 4 ohms nominal or higher are required. The trigger connections link the A1 to a preamplifier and to further amplifiers.

Alternatives

The Emotiva XPA-1 Gen3 is a monoblock with balanced XLR and unbalanced RCA inputs, rated at 300 W into 8 ohms and 600 W into 4 ohms.

Specifications

  • Model name

    BasX A1

  • Input sensitivity (mV)

    1600

  • Input impedance (balanced) (Ω)

    N/A

  • Input impedance (single-ended) (Ω)

    27 000

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    200

  • Output power (4Ω) (W)

    325

  • Gain (dBu)

    29

  • Frequency response low +/- 3dB (Hz)

    5

  • Frequency response high +/- 3dB (Hz)

    80 000

  • Signal to Noise Ratio (dB)

    >112

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    < 0.02

  • Max power consumption (W)

    N/A

  • Damping factor

    > 500

  • Dimensions (mm)

    432 × 102 × 394

  • Weight (kg)

    10

  • Official link

More components