Hifiverse

Integrated amplifiers — Denon PMA-1700NE

Description, images, technical data and specifications

Denon PMA-1700NE
Image source - (c) Denon

The PMA-1700NE is a two-channel integrated amplifier from Denon with an Advanced UHC-MOS single push-pull power amplifier, a USB-DAC and a phono equalizer for MM and MC cartridges. It belongs to the NE series and has no network streaming, Wi-Fi or HEOS. Denon lists it in Black and Silver finishes at GBP 1,615 in the UK and USD 2,299 in the US.

Key specs that matter

Rated output power is 70 W + 70 W (8 ohms, 20 Hz - 20 kHz, THD 0.07%) and 140 W + 140 W (4 ohms, 1 kHz, THD 0.7%). Frequency response is 5 Hz - 100 kHz (0 to -3 dB), THD is 0.01% (rated output -3 dB, 8 ohms, 1 kHz), and damping factor is 100 and over. Phono input sensitivity is 2.5 mV/47 kohms for MM and 200 µV/100 ohms for MC, with RIAA deviation of ±0.5 dB (20 Hz - 20 kHz). Signal-to-noise ratio is 89 dB for MM phono, 74 dB for MC phono and 107 dB for CD. The USB-B input accepts PCM up to 384 kHz/32-bit and DSD up to 11.2 MHz (DoP), and two optical inputs plus one coaxial input accept up to 192 kHz/24-bit. Dimensions are 434 x 135 x 410 mm (W x H x D), and net weight is 17.6 kg.

Engineering and use context

According to Denon, the UHC (Ultra High Current) design ensures drivability of a wide range of speaker types and impedances. Its power transformer has a dual EI core, and the power amplifier sits on extruded aluminium heatsinks. The preamplifier is a variable gain op-amp circuit, and volume, balance and tone use electrical controls with a MUSES 72323 volume IC. Source Direct bypasses all tone controls.

Digital conversion uses a PCM1795 DAC with Advanced AL32 Processing Plus, which Denon describes as data interpolation, up-sampling and bit-extension. The USB-B input works in asynchronous mode with an XMOS module, a DAC master clock design and a high-speed digital isolator against noise from a connected computer. Analog Mode turns off power to the digital input circuitry and stops its operation.

Denon calls the chassis a six-block configuration of 1 mm-thick steel plates with direct mechanical ground construction, standing on ABS resin feet with rigid ribs. On the rear panel are four analogue inputs including phono, a recorder output, EXT. PRE power amp inputs with fixed gain and two sets of speaker terminals for bi-wiring.

Pairing

Speaker impedance is rated 4 - 16 ohms for one pair and 8 - 16 ohms with both pairs connected. The two sets of terminals allow bi-wiring. A turntable with an MM or MC cartridge connects directly. The EXT. PRE input allows the power section to be used with an AV processor.

Alternatives

The Denon PMA-A110 is a limited 110th Anniversary Edition integrated amplifier rated at 80 W per channel.

Specifications

  • Model name

    PMA-1700NE

  • Type

    2 Ch. 140W integrated Amplifier with USB-DAC and Phono

  • Analog inputs (balanced)

    N/A

  • Analog inputs (single-ended)

    3 + 1 (Phono)

  • Input sensitivity (mV)

    850

  • Input impedance (balanced) (Ω)

    N/A

  • Input impedance (single-ended) (Ω)

    N/A

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • D/A conversion

    N/A

  • Phono MM/MC current-sensing input impedance (Ω)

    N/A

  • Output power (8Ω) (W)

    70

  • Output power (4Ω) (W)

    140

  • Gain (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    5

  • Frequency response high +/- 3dB (Hz)

    100 000

  • Signal to Noise Ratio (dB)

    PHONO (MM): 89, PHONO (MC): 74, CD: 107

  • Total Harmonic Distortion + Noise (%)

    0.01

  • Damping factor

    N/A

  • Dimensions (mm)

    434 x 410 x 135

  • Weight (kg)

    17.6

  • Official link

More components