Hifiverse

Tonabnehmer - Clearaudio Performer V2

Beschreibung, Bilder, technische Daten und Spezifikationen

Clearaudio Performer V2
Bildquelle - (c) Clearaudio

The Performer V2 is a moving magnet cartridge from Clearaudio of Erlangen, Germany, and belongs to the MM-V2 series. It pairs an aluminium cantilever and an elliptical diamond with a body of hand-polished ebony. In that series only the concept V2 has a different housing material, aluminium, while every other model uses ebony.

Key specs that matter

Output voltage is about 3.3 mV (1 kHz, 5 cm/s) and frequency response is 20 Hz - 20 kHz. Channel separation is 20 dB and channel balance 1.5 dB, both measured at 1 kHz. Tracking ability is 80 µm. Recommended tracking force is 2.2 g (±0.3 g). Coil impedance is 0.66 kOhm (1 kHz) and coil inductance 400 mH, with a load resistance of 47 kOhm and a capacitive load of 100 pF. Stylus compliance is 15 µ/mN. Mass of the complete system is 8.4 g (±0.4 g). Clearaudio's two-year warranty applies if the completed warranty card is returned within 14 days of purchase.

Engineering and use context

Clearaudio describes its MM Technology V2 as ebony used as a low-resonance housing foundation. Three further measures complete it, namely the lowest practical moving mass, optimised HD grinding of the styli and effective damping of the cartridge.

Each cartridge of this type is measured several times, analysed and hand-selected in four planes. Clearaudio states the aim as homogeneous stereo channels with minimal phase and transient distortion.

All ebony MM-V2 models share one generator specification, with 0.66 kOhm coils, 400 mH inductance and the same recommended load. Stylus, cantilever and selection data separate them. The Artist V2 has the same aluminium cantilever and elliptical diamond, but it is specified at about 3.6 mV output, 24 dB channel separation and 0.8 dB channel balance. In the same series, the Maestro V2 uses a boron cantilever with a Shibata diamond and a compliance of 16 µ/mN. Mounting and setup follow Clearaudio's common instruction manual for the Moving Magnet V2 cartridges.

Pairing

A standard MM phono input is required. Tonearm cable and phono input together should stay close to the specified capacitive load. Clearaudio states that the MM-V2 models work on all common tonearms.

Alternatives

The Clearaudio Artist V2 uses the same ebony body and aluminium cantilever but is rated at about 3.6 mV output and 24 dB of channel separation.

Spezifikationen

  • Modellbezeichnung

    Performer V2

  • Typ

    MM

  • Nadel

    Elliptical

  • Gehäuse

    Ebony wood

  • Nadelträger

    Aluminium

  • Spulen

    N/A

  • Ausgangsspannung (mV@5cm/sec)

    3.3

  • Untere Grenzfrequenz +/- 3dB (Hz)

    20

  • Obere Grenzfrequenz +/- 3dB (Hz)

    20 000

  • Innenwiderstand (Ohm)

    N/A

  • Kanaltrennung (dB / 1,000 Hz)

    20

  • Nadelnachgiebigkeit (×10-6cm/dyne at 100Hz)

    15 μ/mN

  • Empfohlene Abschlussimpedanz (Ohm)

    47 000

  • Empfohlene Tonarme

    N/A

  • Gewicht (g)

    8.4

  • Offizieller Link