Hifiverse

Endstufen Stereo - Burmester 911 MK3

Beschreibung, Bilder, technische Daten und Spezifikationen

Burmester 911 MK3
Bildquelle - (c) Burmester

The 911 MK3 is a stereo power amplifier from the Top Line of Burmester Audiosysteme and the second largest amplifier the Berlin company builds. It is derived from the findings of the 909 power amplifier design. The 911 has been in production since January 1991, and the MK3 is its third generation. Each unit is built by hand in Berlin.

Key specs that matter

Output power into 4 ohms is 2 x 350 W in stereo and 1 x 770 W in mono. The damping factor is 2750, signal-to-noise ratio is above 103 dB and input sensitivity is 770 mV for full output. Power bandwidth is below 10 Hz - 220 kHz (-3 dB). Eight selected power transistors are used per channel. The oversized power supply has 130,000 µF of filtering and a custom-made 750 VA toroidal transformer. Inputs are balanced, for stereo or mono, and unbalanced sources connect through supplied adapters. A 10 V DC input and output provide remote on/off switching. Dimensions are 482 x 216 x 482 mm (W x H x D), and weight is about 31 kg.

Engineering and use context

Like the 808 preamplifier, the 911 MK3 has a modular construction. Its circuit is fully balanced and DC-coupled throughout, without capacitors between input and output. Input stages use Burmester's X-Amp technology in class A. For the MK3 the output stages were completely redesigned, and the internal signal wiring is Burmester SILVER, with pure-silver speaker cable of 8 mm² in total between the output boards and the terminals. Earlier MK1 and MK2 units can be upgraded to MK3 with a new warranty by exchanging the amplifier boards, though the housing colour stays as it was.

Burmester rates the amplifier as stable into all loads across the full frequency range and states that its impulse reproduction is practically load-independent. Mono operation uses external mono bridges, or the amplifier is wired for mono at the factory at no extra cost, which rules out bi-amping. With external bi-amp bridges a pair of amplifiers drives a loudspeaker in bi-amp mode. The channels are matched so closely that the rise time does not change in mono.

A protection circuit outside the signal path monitors temperature and DC offset. The aluminium heat sinks are pressed with Burmester's own tool, and the 8 mm and 10 mm aluminium bottom and lid come from Berlin suppliers. Silver-anodised housing parts and heat sinks identify the MK3, and black heat sinks are available at extra cost. Every unit passes a computer test, a week-long run under load, a second computer test and a listening test, and all test records are archived.

Pairing

A preamplifier with a balanced output is required. Spade lugs are required on the screw terminals. Two units bridged to mono form a monoblock pair.

Alternatives

The 956 MK2 is another stereo power amplifier from Burmester.

Spezifikationen

  • Modellbezeichnung

    911 MK3

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    1

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    N/A

  • Ausgangsleistung (4Ω) (W)

    N/A

  • Verstärkung (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Obere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Signal-Rausch-Abstand (dB)

    N/A

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    N/A

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    N/A

  • Abmessungen (mm)

    N/A

  • Gewicht (kg)

    N/A

  • Offizieller Link

Weitere Komponenten