Hifiverse

Endstufen Stereo - Burmester 218

Beschreibung, Bilder, technische Daten und Spezifikationen

Burmester 218
Bildquelle - (c) Burmester

The 218 is a dual-channel power amplifier from Burmester of Berlin, larger and more powerful than the 216. Its looks are based on the 159, which Burmester describes as the largest and most powerful mono power amplifier in its history. The US list price was quoted at USD 50,000 and later at USD 60,000.

Key specs that matter

Output power in stereo (IEC 62368-1) is 165 W into 8 ohms, 275 W into 4 ohms and 400 W into 2 ohms. A balanced XLR input serves stereo or, with an adapter, mono bridge operation, and unbalanced sources connect via an adapter. Rear panel connections also include a DC input and output for remote on/off (10 V DC switch-on voltage), a BurLink interface and solid screw speaker terminals. Four mains versions exist - 218-240 for 230 - 240 V, 218-220 for 220 V, 218-120 for 110 - 120 V and 218-100 for 100 V, all 50/60 Hz. Standby consumption is 0.46 W (230 V). Dimensions are 496 x 216 x 479 mm (W x H x D), and weight is 42 kg.

Engineering and use context

Burmester specifies a completely symmetrical structure, with input stages in X-Amp technology operating in Class A. Its signal path is completely DC-coupled, without coupling capacitors. Completely new protection circuits sit outside the signal paths, and microcontroller technology monitors the amplifier status and connects it to home control systems through BurLink.

The power supply was redesigned from the ground up, with a ground concept designed for low interference and new signal and cable routing. Support capacitors on the output stage were optimised for impulse reproduction. According to Burmester, the damping factor stays high over the entire frequency range, even at high frequencies, and operation is stable at all loads. A cooling concept matched to the internal structure and housing gives homogeneous heating.

Compared with older predecessor models the overall height grew by only a few millimetres, with extended Burmester cooling fins, so existing racks can still be used. Decorative lines on the cover follow the heat sink. The rear wall is milled from solid and meets the heat sink at a 45 degree angle, a solid base plate closes the housing, and the lid is screwless. Each assembly is 100% tested before installation, followed by several days of trial runs and a final listening test.

Pairing

A preamplifier with balanced XLR outputs is the direct match. Two units can run in mono bridge mode with the adapter. Burmester components switch the 218 on and off remotely.

Alternatives

The 216 is the smaller Burmester stereo power amplifier, rated at 100 W into 8 ohms.

Spezifikationen

  • Modellbezeichnung

    218

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    1900

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    165

  • Ausgangsleistung (4Ω) (W)

    275

  • Verstärkung (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Obere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Signal-Rausch-Abstand (dB)

    N/A

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    N/A

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    N/A

  • Abmessungen (mm)

    496 × 216 × 479

  • Gewicht (kg)

    42

  • Offizieller Link

Weitere Komponenten