Hifiverse

Endstufen Mono - Allnic Audio A-311M

Beschreibung, Bilder, technische Daten und Spezifikationen

Allnic Audio A-311M
Bildquelle - (c) Allnic Audio

The Allnic Audio A-311M is a single-ended tube monoblock that the South Korean maker offers in three versions, each named after its output triode. The buyer picks a 300B, a PX25 or an AD1 when ordering, and the amplifier leaves the factory set up for that one tube type. All three are directly heated triodes, and whichever one is fitted works in Class A only.

Key specs that matter

Output into 8 ohm depends on the chosen triode - 10 W with the 300B, 6 W with the PX25 and 4 W with the AD1. Apart from the output tube, each chassis carries one 5654 small-signal tube and one 5U4G rectifier. Allnic quotes a frequency range of 20 Hz to 20 kHz and total harmonic distortion below 0.1% for all three versions. Every monoblock measures 380 mm wide, 280 mm deep and 190 mm high, so a pair takes up little more shelf space than one conventional stereo power amplifier.

Engineering and use context

The output transformer follows the Full Engagement scheme, with four independent secondary windings that stay connected to the speaker terminals instead of leaving part of the winding unused. Its large core combines nickel and FeSi material, which Allnic chose for high inductance and a wide frequency range. Speaker taps of 4, 8 or 16 ohm are set at the factory to suit the customer. The power transformer holds its voltage regulation under 5%, and two chokes filter the supply, one sitting on the top plate and the other hidden below deck. Each output tube has its own analogue current meter for bias monitoring, and bias is adjusted with simple controls, while a soft-start circuit protects the tubes at switch-on. The design uses only low negative feedback. Left and right units are built as mirror images of each other, so the tube layout stays symmetrical when the pair stands side by side.

Pairing

With single-digit output power in every version, the A-311M belongs with high-efficiency loudspeakers such as horns or large-paper-cone full-range designs, and the AD1 version asks for the most sensitive speakers of all. Because the taps are fixed at the factory, the nominal impedance of the speakers should be known when the order is placed, and a change of speakers later may call for a different secondary connection. A tube line preamplifier from the same maker, or any preamp with enough output voltage, completes the chain.

Alternatives

The Allnic Audio A-5000 DHT is another single-ended monoblock from the brand, fitted with a 300B output triode.

Spezifikationen

  • Modellbezeichnung

    A-311M

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    N/A

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    10 (300B), 6 (PX25), 4 (AD1)

  • Ausgangsleistung (4Ω) (W)

    N/A

  • Verstärkung (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    20

  • Obere Grenzfrequenz +/- 3dB (Hz)

    20 000

  • Signal-Rausch-Abstand (dB)

    N/A

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    0.1

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    N/A

  • Abmessungen (mm)

    380 x 280 x 190

  • Gewicht (kg)

    N/A

  • Offizieller Link