Hifiverse

CD / SACD players and transports — CH Precision D1.5

Description, images, technical data and specifications

CH Precision D1.5
Image source - (c) CH Precision

The D1.5 is an SACD/CD player and transport from CH Precision, designed and manufactured in Preverenges, Switzerland. It is the direct descendant of the D1, the first CH Precision product, and keeps its modular card-cage architecture. In its base version the D1.5 is a pure digital two-channel SACD/CD drive, and optional slot-in boards turn it into a complete player.

Key specs that matter

Supported discs are CD, CD-R, CD-RW and MQA-CD (stereo PCM 16 bit/44.1 kHz) and single-layer and hybrid stereo SACD (DSD 1 bit/2.8224 MHz). The standard digital output board carries CH Link HD, AES/EBU (XLR), S/PDIF (RCA) and S/PDIF (Toslink). With the optional DAC boards, each channel has XLR, RCA and BNC analogue outputs, at 4 V RMS max balanced and 2 V RMS max single-ended. Bandwidth (-3 dB) is DC - 50 kHz on SACD and DC - 20 kHz on CD. THD+N (20 Hz - 20 kHz, A-weighted) is below 0.0015% on SACD and 0.0020% on CD, and S/N is above 120 dB for both. Dynamic range is above 120 dB on SACD and above 96 dB on CD. Power consumption is 40 W nominal and below 0.5 W in standby. Dimensions are 440 x 440 x 133 mm (W x D x H), and weight is 22 kg.

Engineering and use context

MORSe, the Mechanically Optimized Reading System, has critical mechanical parts designed and manufactured in-house. Its optical pick-up and disc drive motor are assembled on a heavy brass module of almost 1 kg. CH Precision states that this mass places the mechanical resonance frequency of the module several orders of magnitude lower than in most transports. Four alpha-gel isolators, tuned to filter vibration down to AC mains frequencies, isolate the module from the chassis. A lightweight PEEK polymer disc clamp gives slip-free transmission from the direct-drive motor, and a 2 kg rigid aluminium structure coupled to the heavy base holds the whole sub-system.

Inside, a linear power supply with an oversized, magnetically shielded toroidal transformer, a mains filter and multiple local regulation stages sits in its own compartment. Its master clock has a dedicated shunt-regulated supply.

A pair of monaural ANALOG_OUT boards upsamples Red Book CD to 352.8 kHz with the PEtER spline algorithm, fully decodes MQA-CD and converts DSD to DXD before conversion. Each Clock Sync board adds one BNC clock input and two outputs for the T1 10 MHz Time Reference, the C1.2 or the I1. When connected, the X1 external power supply replaces the internal supply.

Pairing

The C1.2 DAC/Controller is the matching CH Precision DAC over CH Link HD. Other DACs connect over AES/EBU or S/PDIF. With the ANALOG_OUT boards installed, the D1.5 connects directly to a preamplifier or an integrated amplifier.

Alternatives

The D10 Reference Transport is the higher-level CH Precision disc transport.

Specifications

  • Model name

    D1.5

  • Transport

    Yes

  • Player

    Yes

  • SACD support

    Yes

  • Engine

    N/A

  • Frequency response low +/- 3dB (for CD) (Hz)

    N/A

  • Frequency response high +/- 3dB (for CD) (Hz)

    N/A

  • Frequency response low +/- 3dB (for SACD) (Hz)

    N/A

  • Frequency response high +/- 3dB (for SACD) (Hz)

    N/A

  • Gain (dBu)

    N/A

  • Output Level (balanced) (V)

    N/A

  • Output Level (single-ended) (V)

    N/A

  • Input Impedance (balanced) (Ω)

    N/A

  • Input Impedance (single-ended) (Ω)

    N/A

  • Output Impedance (balanced) (Ω)

    N/A

  • Output Impedance (single-ended) (Ω)

    N/A

  • Dynamic range (for CD) (dB)

    > 96

  • Dynamic range (for SACD) (dB)

    > 120

  • Signal to Noise Ratio (for CD) (dB)

    > 120

  • Signal to Noise Ratio (for SACD) (dB)

    > 120

  • Total Harmonic Distortion + Noise (for CD) (%)

    N/A

  • Total Harmonic Distortion + Noise (for SACD) (%)

    N/A

  • Dimensions (mm)

    440 x 440 x 133

  • Weight (kg)

    27

  • Official link

More components