Hifiverse

Preamplifiers — TAD TAD-C700

Description, images, technical data and specifications

TAD TAD-C700
Image source - (c) TAD

The TAD-C700 is a line-level preamplifier in the Reference Series of TAD Laboratories. It was announced on 25 April 2024 with deliveries from June 2024 at USD 68,500 or CAD 94,500, and it replaced the TAD-C600 of 2011. TAD lists refinements to the preamplification circuit, the dual-mono construction, the power supply and the vibration-suppression techniques. Its power supply is housed in a separate enclosure.

Key specs that matter

Inputs are four balanced and two unbalanced, and outputs are two balanced and two unbalanced. Rated output voltage is 1.5 V balanced and 0.75 V unbalanced, and maximum output voltage is 20 Vrms balanced and 10 Vrms unbalanced. Input impedance is 100 kohms balanced and 50 kohms unbalanced. Frequency response is 10 Hz - 100 kHz (-1 dB), with an S/N ratio of 120 dB. Power consumption is 52 W (0.5 W or less in standby). The main amplifier unit measures 450 x 150 x 440 mm (W x H x D) at 29.0 kg, and the power-supply unit 220 x 185 x 430 mm at 15.0 kg.

Engineering and use context

A fully balanced circuit amplifies the positive and negative signal waveforms individually, with identical wire length and dressing. After the electronic volume control the signal passes a single-stage voltage amplifier, and each of the two line outputs has a dedicated output amplifier circuit, so the signal is never branched. Volume is set by a custom-made electronic volume control with ladder-resistance switching, one for each channel. TAD specifies an absolute error of 0.1 dB or less at more than 100 dB of attenuation and distortion below 0.0005% at 1 Vrms input. Each input has its own sensitivity pre-adjustment.

Inside the outboard power-supply unit is a 400 VA toroidal transformer, a rating TAD calls unheard-of in preamplifiers. Its separate enclosure keeps transformer vibration and magnetic flux leakage away from the audio circuits. Lead-wire terminals, board mounting terminals and clamping screws are oxygen-free copper with a nonmagnetic coating. In the main unit the control keys, LED display and indicators run on direct current, and the control wiring sits in a shielded box in the middle of the enclosure. Its 33 mm thick sub-chassis is made from pure aluminium ingots and weighs 15 kg, and spike-shaped three-point feet support the unit.

Pairing

The recording output has no monitor switch, and an audio pass-through mode sends the input signal to a pre-out jack at unchanged level. Extreme Link controls slave C700 units from the MASTER OUT jack, for dual-mono use with monaural power amplifiers or for three or more channels.

Alternatives

The TAD-C1000 is the line preamplifier of the Evolution series, with the same four balanced and two unbalanced inputs.

Specifications

  • Model name

    TAD-C700

  • Analog inputs (balanced)

    4

  • Analog inputs (single-ended)

    2

  • Analog outputs (balanced)

    2

  • Analog outputs (single-ended)

    2

  • Gain (dBu)

    N/A

  • Input sensitivity (mV)

    N/A

  • Output voltage (V)

    N/A

  • Input impedance (balanced) (Ω)

    100 000

  • Input impedance (single-ended) (Ω)

    50 000

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Maximum output level (balanced) (dBu)

    N/A

  • Maximum output level (single-ended) (dBu)

    N/A

  • Volume control range (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    10

  • Frequency response high +/- 3dB (Hz)

    100 000

  • Signal to Noise Ratio (SNR, unweighted) (dB)

    120

  • Total Harmonic Distortion + Noise (THD+N) (%)

    N/A

  • Dimensions (mm)

    450 x 150 x 440 + 220 x 185 x 430 (supply)

  • Weight (kg)

    29 + 15 (supply)

  • Official link

More components