Hifiverse

Preamplifiers — ModWright Instruments LS300

Description, images, technical data and specifications

ModWright Instruments LS300
Image source - (c) ModWright Instruments

The ModWright LS300 is a tube line preamplifier from ModWright Instruments that uses dual mono construction and an external power supply. The maker describes the circuit as pure Class A, fully balanced from input to output and free of negative feedback. It sits above the LS 99 in the brand's range of line stages.

Key specs that matter

Gain is 11 dB, with input impedance of 20 kohm and output impedance of 100 ohm. Frequency response runs from 20 Hz to 100 kHz, with the 100 kHz point at minus 1 dB. Noise is quoted at minus 115 dB and distortion at less than 0.03% THD at 1 kHz. The inputs comprise two XLR balanced sets and three RCA pairs, one of which doubles as a home theater bypass. Outputs are two fully balanced XLR main pairs and two RCA pairs. The preamplifier measures 432 mm across, 203 mm tall and 318 mm deep, weighing 13.6 kg, and the external supply is 203 x 114 x 254 mm and 7.7 kg.

Engineering and use context

Its tube complement is two 6DJ8 drivers, which also accept 6922 and 7308 types, and two 5R4GY rectifier tubes in the separate supply. Moving the power transformers and rectification into their own case keeps them away from the dual mono audio circuits, and the lack of negative feedback relies on the tube stages' own linearity. The front panel carries input selection, power, mute, the HT/BP bypass switch and a phase control. The remote covers volume, mute, power and phase invert, so absolute polarity can be flipped from the listening seat for recordings that need it. With the bypass engaged, a surround processor passes through at a fixed level to the power amplifier, letting a stereo system share its loudspeakers with a home cinema setup.

Pairing

An XLR-equipped power amplifier makes full use of the balanced circuit, and the two main output pairs allow bi-amping or feeding a second amplifier or a subwoofer. Long interconnect runs pose no problem for its low output impedance. A DAC with XLR outputs is the natural source for the balanced inputs, while single-ended gear such as a phono stage goes to the RCA inputs. The rack needs space for two separate heavy boxes, and the tall main chassis calls for a generous shelf. The input impedance is still an easy load for typical solid-state and tube sources.

Alternatives

The ModWright LS 99 is the brand's smaller balanced tube line stage, with a 150 kHz flat bandwidth.

Specifications

  • Model name

    LS300

  • Analog inputs (balanced)

    2

  • Analog inputs (single-ended)

    3

  • Analog outputs (balanced)

    2

  • Analog outputs (single-ended)

    2

  • Gain (dBu)

    11

  • Input sensitivity (mV)

    N/A

  • Output voltage (V)

    N/A

  • Input impedance (balanced) (Ω)

    20 000

  • Input impedance (single-ended) (Ω)

    20 000

  • Output impedance (balanced) (Ω)

    100

  • Output impedance (single-ended) (Ω)

    100

  • Maximum output level (balanced) (dBu)

    N/A

  • Maximum output level (single-ended) (dBu)

    N/A

  • Volume control range (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    20

  • Frequency response high +/- 3dB (Hz)

    100 000

  • Signal to Noise Ratio (SNR, unweighted) (dB)

    115

  • Total Harmonic Distortion + Noise (THD+N) (%)

    <0.03

  • Dimensions (mm)

    431.8 x 203 x 317.5

  • Weight (kg)

    13.6 + 7.71 (Supply Power)

  • Official link