Hifiverse

Power amplifiers stereo — TAD TAD-M2500MK2

Description, images, technical data and specifications

TAD TAD-M2500MK2
Image source - (c) TAD

The TAD-M2500MK2 is a two-channel power amplifier in the Evolution series of TAD Laboratories, the Japanese company whose name stands for Technical Audio Devices. Evolution sits below the Reference components in the TAD range, and the MK2 replaced the original M2500. The UK price is GBP 24,000. Two finishes are offered - a silver upper half over a black lower half, or all black.

Key specs that matter

Power output is 250 W into 8 ohms and 500 W into 4 ohms (2 channels simultaneously driven, 20 Hz - 20 kHz, 1.0% THD). Rated distortion is less than 0.05% (20 Hz - 20 kHz, 250 W, 4 ohms). Frequency response is 5 Hz - 50 kHz (-3 dB) and 10 Hz - 100 kHz (-1 dB). Signal-to-noise ratio is 112 dB or higher (IHF, short-circuited, A-network), and balanced gain is 29.5 dB. Input sensitivity and impedance are 1.5 V/220 kohms balanced and 0.75 V/47 kohms unbalanced. Power consumption is 250 W, with less than 0.5 W in standby. Dimensions are 440 x 170 x 467 mm (W x H x D), and weight is 43 kg.

Engineering and use context

TAD uses Class D circuitry in a completely balanced structure. Left and right channels are separated from input to output, and the power supplies and transformers are split both between the channels and between the positive and negative rails. Each channel is a bridged transformer-less design with two amplifiers in a balanced configuration.

Its analogue power supply is equipped with a large toroidal power transformer of grain-oriented steel and with TAD's proprietary 33,000 µF electrolytic capacitors. According to TAD, the strong coupling between primary and secondary windings gives low energy conversion loss, and parallel winding gives low load fluctuation. In the Class D output stage are power MOSFETs with very low on-resistance and no lead wires. Heat generation stays low enough that no traditional heat sinks are used.

A 90 kg block of aluminium is machined into the chassis, so there are no joints other than the connections. TAD states that this stabilises the ground potential and gives both high stiffness and high internal loss. A three-point cast-iron insulator damps vibration transmitted through the feet, and the front panel has no visible screws.

Pairing

The matching Evolution preamplifier is the TAD-C1000. Its XLR inputs take a balanced preamplifier output. Full rated output is available into 4 ohms as well as 8 ohms. Mains versions are 120 V 60 Hz for the USA and 220 - 230 V for Europe and Asia.

Alternatives

The TAD-M1000TX is another Evolution stereo power amplifier, a BTL Class D design rated at 500 W per channel into 4 ohms at 1 kHz.

Specifications

  • Model name

    TAD-M2500MK2

  • Input sensitivity (mV)

    N/A

  • Input impedance (balanced) (Ω)

    N/A

  • Input impedance (single-ended) (Ω)

    N/A

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    250

  • Output power (4Ω) (W)

    500

  • Gain (dBu)

    29.5

  • Frequency response low +/- 3dB (Hz)

    5

  • Frequency response high +/- 3dB (Hz)

    50 000

  • Signal to Noise Ratio (dB)

    112

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    <0.05

  • Max power consumption (W)

    250

  • Damping factor

    N/A

  • Dimensions (mm)

    440 x 170 x 467

  • Weight (kg)

    43

  • Official link

More components