Hifiverse

Power amplifiers stereo - Musical Fidelity NU-VISTA PAS

Description, images, technical data and specifications

Musical Fidelity NU-VISTA PAS
Image source - (c) Musical Fidelity

The Nu-Vista PAS is a stereo, fully balanced and discrete power amplifier from Musical Fidelity, supplied with the separate Nu-Vista PAS PSU in a matching box. Based on the earlier Nu-Vista 800 circuit, it belongs to the fully balanced Nu-Vista system together with the Nu-Vista PRE preamplifier and the Nu-Vista PAM monoblocks. Its input stage uses nuvistor tubes in a Class A buffer.

Key specs that matter

Output power is greater than 300 W into 8 ohms, 500 W into 4 ohms and 1000 W peaks into 2 ohms. Output voltage is 49 V RMS, output current 130 A peak to peak, and damping factor 200. There are five pairs of output devices per channel. Gain is 16x (23.5 dB), input impedance 100 kohms, and input sensitivity for full output 3 V RMS. THD+N is below 0.003% typical, 20 Hz - 20 kHz, signal-to-noise ratio exceeds 108 dB (A-weighted), channel separation exceeds 96 dB, and frequency response is +0, -1 dB from 5 Hz to 50 kHz. Inputs are two RCA and two XLR, with two loop-through outputs (one RCA, one XLR). Both boxes measure 483 x 187.5 x 475 mm (W x H x D), and net weight is 27 kg for the amplifier and 40 kg for the PSU.

Engineering and use context

Eight 6S51N nuvistors work in a balanced buffer input circuit, a discrete Class A stage. After it come a balanced configuration circuit and a balanced-input, high-power, low-distortion output stage. Musical Fidelity bases this stage on its Titan 1000 W design, with thermally compensated output devices, separate capacitors for the bulk supply and one capacitor for each output device to reduce output impedance. Chokes further reduce supply ripple and pulse current spikes. Bias is set for over 5 W of initial Class A operation, after which the stage slides into Class B, where the discontinuity is lower than standard crossover distortion.

All transformers are housed in the PAS PSU, away from the amplifier circuits, and the PSU has built-in mains and output filtering. Front and side panels are milled from extruded aluminium, and the case acts as a Faraday cage. A dimmable colour display shows the selected input or optional VU meters. Musical Fidelity notes that nuvistors were invented in the 1950s and offer high reliability, low microphony, low noise and batch consistency.

Pairing

The matching preamplifier is the Nu-Vista PRE, and the fully balanced XLR inputs accept any balanced preamplifier. Its loop-through outputs allow bi-amping with a second amplifier. Speaker outputs are two pairs of 4 mm banana/binding posts per side, and a 3.5 mm trigger input and output (±5 V to ±12 V) allow system switching.

Alternatives

The Musical Fidelity M6S PRX is a smaller dual mono stereo power amplifier with a choke-regulated supply.

Specifications

  • Model name

    NU-VISTA PAS

  • Input sensitivity (mV)

    N/A

  • Input impedance (balanced) (Ω)

    100 000

  • Input impedance (single-ended) (Ω)

    100 000

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    300

  • Output power (4Ω) (W)

    500

  • Gain (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    5

  • Frequency response high +/- 3dB (Hz)

    50 000

  • Signal to Noise Ratio (dB)

    >108

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    < 0.003

  • Max power consumption (W)

    1600

  • Damping factor

    200

  • Dimensions (mm)

    483 x 187,5 x 475

  • Weight (kg)

    40

  • Official link

More components