Hifiverse

Power amplifiers stereo — Luxman M-700u

Description, images, technical data and specifications

Luxman M-700u
Image source - (c) Luxman

The M-700u is a stereo power amplifier that Luxman of Japan introduced as a middle-range model in its solid-state line. It carries the ODNF 4.0 feedback circuit over from the M-900u, which Luxman named its top-end model at the time, and it can be switched to BTL mode for use as a monaural amplifier.

Key specs that matter

Rated output is 120 W + 120 W into 8 ohms and 210 W + 210 W into 4 ohms in stereo, and 420 W into 8 ohms in monaural mode. Instantaneous maximum output is 840 W + 840 W into 1 ohm in stereo and 1,680 W into 2 ohms in mono. Input sensitivity is 1.1 V for 120 W into 8 ohms, with a gain of 29.0 dB. Input impedance is 51 kohms unbalanced and 34 kohms balanced. Frequency response is 20 Hz - 20 kHz (+0, -0.1 dB) and 1 Hz - 130 kHz (+0, -3 dB). THD is 0.009% or less at 1 kHz into 8 ohms and 0.1% or less from 20 Hz to 20 kHz. S/N (IHF-A) is 115 dB, and the damping factor is 350. Power consumption is 370 W, 110 W with no signal and 0.4 W in standby. It measures 440 x 190 x 427 mm and weighs 27.5 kg.

Engineering and use context

ODNF stands for Only Distortion Negative Feedback. Luxman states that version 4.0 improves distortion characteristics and S/N performance over earlier versions, and it also cites a higher primary slew rate and ultra-wide bandwidth.

Each channel has a bipolar push-pull output stage with four parallel pairs in a three-stage Darlington configuration. Its power supply is built on an EI-type power transformer rated at 550 VA, with 80,000 uF of block capacitance made up of eight 10,000 uF capacitors.

Main current paths use super-thick wire. Luxman calls its internal layout Beeline construction, with the shortest possible wiring route and copper-foil board wiring of about 100 um. A loopless chassis structure is used for the cabinet. On the front panel, two large needle-type meters are LED-illuminated, and a switch sets them to three states - meters and lights on, meters on with lights off, or both off.

Speaker terminals accept Y-lugs up to 14 mm wide at the fork, though some lug shapes may not fit. A dedicated remote cable and a power cable come in the box.

Pairing

A preamplifier with a standard line output is required. In monaural mode two units are required for a stereo system. Balanced and unbalanced inputs allow either connection from the preamplifier.

Alternatives

The Luxman M-10X is the stereo power amplifier above it in the range and uses the newer LIFES feedback engine.

Specifications

  • Model name

    M-700u

  • Input sensitivity (mV)

    1100

  • Input impedance (balanced) (Ω)

    34 000

  • Input impedance (single-ended) (Ω)

    51 000

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    120

  • Output power (4Ω) (W)

    210

  • Gain (dBu)

    29

  • Frequency response low +/- 3dB (Hz)

    1

  • Frequency response high +/- 3dB (Hz)

    130 000

  • Signal to Noise Ratio (dB)

    115

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    0.1

  • Max power consumption (W)

    370

  • Damping factor

    350

  • Dimensions (mm)

    440 x 190 x 427

  • Weight (kg)

    27.5

  • Official link

More components