Hifiverse

Power amplifiers stereo — Bryston BD-325

Description, images, technical data and specifications

Bryston BD-325
Image source - (c) Bryston

The BD-325 is the higher-powered model of the BD series, the first Class D power amplifiers from Bryston, which builds them in Dwight, Ontario, Canada. Like the BD-225, it uses a common chassis that holds one to six independent Class D modules, and it is ordered as a mono, stereo or multichannel amplifier from the same design.

Key specs that matter

Rated continuous output is 325 W RMS per channel into 8 ohms and 650 W into 4 ohms. All channels together are rated at 1,500 W continuous and 4,500 W dynamic (100 ms). Frequency response is 1 Hz - 50 kHz (6 ohms, -3 dB). Input sensitivity is 2 V, voltage gain is 29 dB and signal-to-noise ratio is 105 dB at full power. Storage capacitance is 144,000 µF. Inputs are balanced XLR and single-ended RCA, plus a 12 V trigger input. It runs on 115 or 230 V mains. Its chassis measures 133 x 450 x 425 mm (H x W x D) and weighs 26 kg.

Engineering and use context

Inside, Bryston's proprietary Class D modules are powered by a linear supply with a toroidal transformer and large storage capacitance, not by the switching supply common in Class D amplifiers. Bryston names that switching supply as one of the concerns with Class D designs. Each module uses pulse width modulation, a MOSFET switching transistor and an output low-pass filter that returns the signal to analogue form. Heat is removed by passive heat sinks, and no fans are used.

According to the owner's manual, the amplifier is a discrete multi-channel design housed in a single chassis, with every channel independent. Multichannel active or passive systems and custom-install zones are the uses Bryston gives for the modular layout. Mains power connects through an IEC-320 C14 inlet. Operation and standby are set with a rear mains switch and a front push button, and a blue LED indicates power-on. The 12 V trigger connection is a 3.5 mm jack. Its binding posts take banana plugs, spade lugs up to 16 mm wide (8 mm post) or bare wire up to 3 gauge. Personalised and custom faceplate colours are available. Bryston's owner's manual states a five-year warranty.

Pairing

A preamplifier or AV processor with XLR or RCA outputs is required, with one cable type per channel. A 12 V trigger output on the preamplifier allows remote switch-on.

Alternatives

The Bryston BD-225 is the lower-powered BD model, with 225 W per channel into 8 ohms, 450 W into 4 ohms and 1.5 V input sensitivity.

Specifications

  • Model name

    BD-325

  • Input sensitivity (mV)

    2000

  • Input impedance (balanced) (Ω)

    N/A

  • Input impedance (single-ended) (Ω)

    N/A

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    325

  • Output power (4Ω) (W)

    650

  • Gain (dBu)

    29

  • Frequency response low +/- 3dB (Hz)

    1

  • Frequency response high +/- 3dB (Hz)

    50 000

  • Signal to Noise Ratio (dB)

    105

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    N/A

  • Max power consumption (W)

    N/A

  • Damping factor

    N/A

  • Dimensions (mm)

    133 x 450 x 425

  • Weight (kg)

    26

  • Official link

More components