Hifiverse

Power amplifiers stereo - Emotiva BasX A3

Description, images, technical data and specifications

Emotiva BasX A3
Image source - (c) Emotiva

The BasX A3 is a three-channel power amplifier from Emotiva, announced on 8 April 2021 together with the BasX A2, A4, A5 and A7 at a launch price of USD 499. According to Emotiva, it provides the channels needed to upgrade a two-channel system to 5.1 surround sound. The BasX A3+ later replaced it.

Key specs that matter

With all channels driven, output is 140 W RMS per channel into 8 ohms (20 Hz - 20 kHz, THD < 0.1%) and 200 W RMS per channel into 4 ohms (1 kHz, THD < 1%). With two channels driven, it is rated at 150 W per channel into 8 ohms and 250 W per channel into 4 ohms. Power bandwidth is 20 Hz - 20 kHz (±0.07 dB) or better, and broad band frequency response is 5 Hz - 80 kHz (+0/-1.8 dB). THD+N is < 0.02% (A-weighted, rated power, 1 kHz, 8 ohms). Signal-to-noise ratio is > 112 dB referenced to rated power and > 95 dB referenced to 1 W (A-weighted). Damping factor is > 500 into 8 ohms. Input sensitivity is 1.25 V for rated power, gain is 29 dB and input impedance is 27 kohms. Rated load is 8 ohms, minimum load 4 ohms. Size is 432 x 108 x 394 mm (W x H x D) with feet, 89 mm high without them, and weight is 11.4 kg.

Engineering and use context

Each channel uses a fully discrete, high-current, short signal path Class A/B output section. A heavy-duty linear power supply with an oversized toroidal transformer powers all three. Inputs are unbalanced RCA, one per channel, and there are no XLR inputs. Speaker outputs are 5-way binding posts, and mains enters through a standard IEC inlet.

Trigger input accepts 5 - 12 V (AC or DC) at less than 10 mA, and the trigger output supplies 12 VDC for loads up to 120 mA. Auto-On signal sensing is not provided on this model, only on the BasX A2. Mains voltage of 115 or 230 VAC at 50/60 Hz is detected automatically. Protection covers excessive operating temperature, shorted speaker connections and ground faults. On a fault the blue per-channel status LEDs flash red while the amber standby LED flashes, and a rear switch disables the status LEDs. Emotiva builds the A3 on a heavy steel chassis with a milled aluminium face plate and gives a three-year warranty.

Pairing

An AV receiver or processor with RCA pre-outs is required. Speakers of 4 ohms or higher are within the rated load. A processor with XLR outputs only needs adapters.

Alternatives

The BasX A3+ is the later three-channel model, with balanced XLR inputs added beside the RCA inputs.

Specifications

  • Model name

    BasX A3

  • Input sensitivity (mV)

    N/A

  • Input impedance (balanced) (Ω)

    N/A

  • Input impedance (single-ended) (Ω)

    27 000

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    140

  • Output power (4Ω) (W)

    200

  • Gain (dBu)

    29

  • Frequency response low +/- 3dB (Hz)

    10

  • Frequency response high +/- 3dB (Hz)

    80 000

  • Signal to Noise Ratio (dB)

    >112

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    < 0.02

  • Max power consumption (W)

    N/A

  • Damping factor

    > 500

  • Dimensions (mm)

    432 × 103 × 394

  • Weight (kg)

    13,2

  • Official link

More components