Hifiverse

Power amplifiers stereo — Accustic Arts AMP IV

Description, images, technical data and specifications

Accustic Arts AMP IV
Image source - (c) Accustic Arts

The AMP IV is a stereo power amplifier from Accustic Arts of Lauffen, handmade in Germany. Its maker calls it its bestseller and presents it as a reference class design in its 5th generation. It is a dual-mono amplifier with a completely isolated power supply for each channel. US pricing has been USD 40,990 with chrome trim and USD 42,990 with gold trim.

Key specs that matter

Rated power output at THD+N 0.1% is max. 2 x 810 W into 2 ohms, 2 x 620 W into 4 ohms and 2 x 400 W into 8 ohms, and the minimum impedance is 2 ohms. Voltage gain is 25.0 dB. Frequency response is 10 Hz - 50 kHz (+0/-0.5 dB) at 10 W into 4 ohms. THD+N measures 0.003% into 4 ohms at 1 kHz and 10 W, signal-to-noise ratio is -103 dBA (ref. 6.325 V) and crosstalk is 109 dB at 1 kHz. Input impedance is 2 x 16 kohms on XLR and 15 kohms on RCA. Idle current is approx. 300 mA, and power consumption without load is approx. 120 W. Dimensions are 340 x 470 x 440 mm (H x W x D), and weight is approx. 44 kg, with 12 kg more for the flight case.

Engineering and use context

Twenty selected MOS-FET output transistors make up the output stage. Each channel has its own magnetically shielded and encapsulated toroidal core transformer, protected by its own fuse (FUSE 1 and FUSE 2). Power supply capacity is more than 160,000 µF, in capacitors made in Germany. Generously dimensioned heat sinks keep the operating temperature constant and low.

Accustic Arts specifies a very high damping factor. Its damping factor linearization is switched by a DAMPING CONTROL button on the rear. In the ON position it lowers the damping factor slightly and linearises it over a wide frequency range, and in the OFF position the damping factor is maximised but decreases considerably from 5 kHz. A protective circuit acts against clipping, HF oscillations and too high DC offset, together with integrated switch-on current limitation. One red LED per channel shows protection mode during warm-up or an error, and a blue LED shows that the unit is ready.

There are two XLR and two RCA inputs, selected by an INPUT SELECTION button, and only one input type is active at a time. A MUTE switch turns off the speaker outputs. Both channels have WBT terminal pairs A and B plus a ground contact for shielded speaker cables. The housing is massive, resonance-optimised aluminium, with a polished and chromed inlay of massive brass.

Pairing

A preamplifier with a balanced XLR or unbalanced RCA output is required. The gold-plated WBT terminal pairs allow bi-wiring or bi-amping.

Alternatives

The AMP VI is the larger stereo power amplifier in the Accustic Arts REFERENCE-SERIES, with 40 MOS-FET output transistors.

Specifications

  • Model name

    AMP IV

  • Input sensitivity (mV)

    N/A

  • Input impedance (balanced) (Ω)

    16 000

  • Input impedance (single-ended) (Ω)

    15 000

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    400

  • Output power (4Ω) (W)

    620

  • Gain (dBu)

    25

  • Frequency response low +/- 3dB (Hz)

    10

  • Frequency response high +/- 3dB (Hz)

    50 000

  • Signal to Noise Ratio (dB)

    103

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    0.003

  • Max power consumption (W)

    120

  • Damping factor

    N/A

  • Dimensions (mm)

    340 x 470 x 440

  • Weight (kg)

    44

  • Official link

More components