Hifiverse

Integrated amplifiers — Vitus Audio SIA-030

Description, images, technical data and specifications

Vitus Audio SIA-030
Image source - (c) Vitus Audio

The SIA-030 is an integrated amplifier from Vitus Audio of Herning, Denmark, and sits midway in the Vitus range, in the Signature Series. Vitus designed it as a step up from the SIA-025 with more power and more options, in a modular chassis with an optional DAC/streamer module. Standard finishes are Pure White, Jet Black and Warm Silver, and Titanium Orange, Dark Champagne and Titanium Grey are offered as unique colours.

Key specs that matter

Output power is approximately 200 W per channel in class AB or 30 W in class A into 8 ohms, and 400 W or 60 W into 4 ohms. Inputs are three balanced XLR and two RCA pairs, each with 10 kohm impedance and 2, 4 or 8 V RMS sensitivity. Frequency response extends beyond 800 kHz. Signal-to-noise ratio is above 120 dB at 1 kHz and THD + noise is below 0.01%. Speaker output impedance is 0.075 ohms, and an RCA pre-out with 33 ohm output impedance is provided. Power consumption is below 1 W in standby, about 180 W in class AB and about 280 W in class A. The chassis is 270 mm high including feet, 435 mm wide and 500 mm deep (532 mm with binding posts), and it weighs 63 kg.

Engineering and use context

Class A and class AB operation are selectable. A second setting chooses between Classic and Rock modes, and Vitus states that these modes reconfigure the output stage without filtering or changes to the signal path. Both settings can be combined.

Volume is controlled by a relay-switched fixed resistor network from -89 dB to +13 dB in 0.5 dB steps. The SIA-030 uses technology from the top-tier Masterpiece (MP) series of Vitus. Both the preamplifier stage and the output stages are powered by a fully regulated power supply, and the circuits are discrete. Body parts and heat sinks are aluminium.

The optional plug-and-play DAC/streamer module has an AES input, an S/PDIF RCA input, an optical input, Ethernet for streaming and a USB input supporting DSD up to 2x. A phono module for MM and MC cartridges with up to 70 dB of gain is listed but not currently available. Software updates are installed from a .bin file on a USB drive through the service port.

Pairing

A separate phono stage is required for vinyl, and the matching model is the MP-P201 Mk.III. The pre-out allows a second power amplifier or a subwoofer.

Alternatives

The SIA-025 Mk.II is the smaller integrated amplifier of the same Signature Series.

Specifications

  • Model name

    SIA-030

  • Type

    Integrated Amplifier

  • Analog inputs (balanced)

    3

  • Analog inputs (single-ended)

    2

  • Input sensitivity (mV)

    8000

  • Input impedance (balanced) (Ω)

    10 000

  • Input impedance (single-ended) (Ω)

    10 000

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • D/A conversion

    N/A

  • Phono MM/MC current-sensing input impedance (Ω)

    N/A

  • Output power (8Ω) (W)

    200 (AB) + 30 (A)

  • Output power (4Ω) (W)

    400 (AB) + 60 (A)

  • Gain (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    N/A

  • Frequency response high +/- 3dB (Hz)

    800 000

  • Signal to Noise Ratio (dB)

    >120

  • Total Harmonic Distortion + Noise (%)

    <0.01

  • Damping factor

    N/A

  • Dimensions (mm)

    270 × 435 × 523

  • Weight (kg)

    63

  • Official link

More components