Hifiverse

Integrated amplifiers — Vitus Audio SIA-025 MK.II

Description, images, technical data and specifications

Vitus Audio SIA-025 MK.II
Image source - (c) Vitus Audio

The SIA-025 Mk.II is an integrated amplifier in the Signature Series of Vitus Audio, made in Herning, Denmark. Its predecessor, the SIA-025, was the first integrated amplifier of the Signature Series, created after Vitus followers asked for a more compact system. In the Mk.II, fully integrated circuitry shares the chassis of the SS-010 stereo power amplifier, and Vitus says this was done with no sacrifice in size or noise.

Key specs that matter

Rated power is approximately 25 W RMS in Class A and 150 W RMS in Class AB per channel into 8 ohms, rising to approximately 50 W and 300 W into 4 ohms. Inputs are three balanced XLR and two RCA pairs, each with 2, 4 or 8 Vrms sensitivity and 10 kohms impedance. Speaker output impedance is 0.075 ohms, and the XLR pre out has 33 ohms. Frequency response extends to +800 kHz, signal-to-noise ratio is >100 dB at 1 kHz and THD+N is <0.01%. Power consumption without load is 90 W in Class AB and 162 W in Class A, with <1 W in standby. It measures 435 x 135 x 436 mm (W x H x D), height including feet, depth 471 mm with binding posts, and weighs 37 kg.

Engineering and use context

Vitus applies its rule that no component is required to deliver more than 25% of what it is capable of handling, for longer component life and a lower risk of failure. This is a true balanced amplifier with balanced speaker outputs, so the negative speaker terminal must not be connected to chassis or signal ground. Body parts and heat sinks are aluminium.

Class AB is the standard mode of operation. Class A is selected in the menu and resets to Class AB whenever the unit is put into standby. Volume is set by a relay controlled fixed resistor network from -81 dB to +11 dB in 1 dB steps. Each input has its own volume offset of -12 dB to +12 dB, and any input can be locked to a fixed volume step as a home theater bypass for an external surround processor. An automatic standby timer is also in the menu.

Mains voltage is set for 100 V, 115 V or 230/240 V AC and can be changed. Supplied with the amplifier are the RC-010 remote control with its charger, a power cable and a USB stick with the manual. Pure White, Jet Black and Warm Silver are standard colours, while Titanium Orange, Dark Champagne and Titanium Grey are the most requested unique finishes, and bespoke colours and internal configurations are offered.

Pairing

Speaker cables with spade or banana terminations are required. The XLR pre out is intended for bi-amping with a separate power amplifier. A surround processor connects to an input set to fixed volume.

Alternatives

The SIA-030 is the other integrated amplifier in the Vitus Audio Signature Series.

Specifications

  • Model name

    SIA-025 MK.II

  • Type

    Integrated Amplifier

  • Analog inputs (balanced)

    3

  • Analog inputs (single-ended)

    2

  • Input sensitivity (mV)

    2000 / 4000 / 8000

  • Input impedance (balanced) (Ω)

    10 000

  • Input impedance (single-ended) (Ω)

    10 000

  • Output impedance (balanced) (Ω)

    33

  • Output impedance (single-ended) (Ω)

    N/A

  • D/A conversion

    N/A

  • Phono MM/MC current-sensing input impedance (Ω)

    N/A

  • Output power (8Ω) (W)

    150

  • Output power (4Ω) (W)

    300

  • Gain (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    N/A

  • Frequency response high +/- 3dB (Hz)

    800 000

  • Signal to Noise Ratio (dB)

    >100

  • Total Harmonic Distortion + Noise (%)

    <0.01

  • Damping factor

    N/A

  • Dimensions (mm)

    135 × 435 × 436

  • Weight (kg)

    37

  • Official link