Hifiverse

Plattenspieler - Audio-Technica AT-LP60XBT

Beschreibung, Bilder, technische Daten und Spezifikationen

Audio-Technica AT-LP60XBT
Bildquelle - (c) Audio-Technica

The AT-LP60XBT is a belt-drive turntable with fully automatic operation and a Bluetooth transmitter from Audio-Technica. It is the wireless version of the LP60X platform, with a built-in phono equalizer and an AT3600L cartridge pre-mounted on the headshell. Two finishes were listed at launch - black as AT-LP60XBT-BK and white with black as AT-LP60XBT-WH. In the UK it launched at GBP 179, or EUR 199 in the eurozone.

Key specs that matter

Speeds are 33-1/3 and 45 RPM, driven by a DC servo-controlled motor. The platter is aluminium. Wow and flutter is below 0.25% (WTD) at 3 kHz, and signal-to-noise ratio is above 50 dB (DIN-B). Cartridge type is VM, with the ATN3600L as the replacement stylus. Output level is 2.5 mV nominal in PHONO position and 150 mV nominal in LINE position (1 kHz, 5 cm/sec), and phono pre-amp gain is 36 dB nominal with RIAA equalisation. Bluetooth is version 5.0 with A2DP, the Qualcomm aptX and SBC codecs, a maximum RF output of 10 mW EIRP and a range of approx. 10 m in line of sight (2.402 - 2.480 GHz, FHSS). Power requirements are 100 - 240 V, 50/60 Hz, with an external 12 V, 2 A AC adapter and a consumption of 1.5 W. Dimensions are 359.5 x 97.5 x 373.3 mm (W x H x D), and weight is 2.6 kg.

Engineering and use context

The platter is supplied with its drive belt, which is placed on a brass-coloured motor pulley during setup. A felt mat sits on the platter. Operation is automatic - the START button spins the platter and moves the tonearm, and STOP returns the arm to its original position and stops the platter. A separate tonearm lift button lifts and lowers the arm for manual track selection, and a size selector is switched between 305 mm and 178 mm according to the record size.

On the rear panel a pre-amplifier selector switch chooses between PHONO and LINE output at the stereo RCA terminals. The wireless function button connects the turntable to a Bluetooth device, and an indicator LED shows the connection status. Audio-Technica specifies that pairing information for up to eight devices is stored. The replacement belt is an AT-LP60X exclusive part. Accessories are a hinged dust cover, the 45 RPM adapter, an RCA audio cable of approx. 1.2 m and an AC adapter of approx. 1.5 m.

Pairing

For a wireless link, a Bluetooth speaker or headphones with A2DP are required, and aptX is used where the receiver supports it. In PHONO position the cable goes to a phono input and its ground terminal. In LINE position it goes to an AUX or line input of an amplifier, receiver or active speakers.

Alternatives

The AT-LP60XBT-USB is the same automatic Bluetooth turntable with an added USB output for recording records to a computer.

Spezifikationen

  • Modellbezeichnung

    AT-LP60XBT

  • Geschwindigkeit

    33/45

  • Antrieb

    Belt

  • Subchassis/Aufhängung

    N/A

  • Tonarm vorinstalliert

    Ja

  • Tonarmmodell

    N/A

  • Tonabnehmer vorinstalliert

    k. A.

  • Tonabnehmermodell

    N/A

  • Plattenteller

    Aluminum

  • Motor

    DC

  • Gleichlaufschwankungen (%)

    N/A

  • Signal-Rausch-Abstand (dB)

    >50

  • Rumpelgeräusch (-dB)

    N/A

  • Abmessungen (mm)

    359.5 x 97.5 x 373.3

  • Gewicht (kg)

    N/A

  • Offizieller Link