Hifiverse

Standlautsprecher - Magnepan Magnepan 1.7i

Beschreibung, Bilder, technische Daten und Spezifikationen

Magnepan Magnepan 1.7i
Bildquelle - (c) Magnepan

The MG1.7i is a three-way, full-range Magneplanar loudspeaker from Magnepan of White Bear Lake, Minnesota. Its suffix i stands for improved, and the model follows the MG1.7, introduced in July 2010 at USD 1,995 per pair. A pair of MG1.7i is listed at USD 2,995, and the model is also built as the upgraded MG1.7x.

Key specs that matter

Magnepan's manual quotes a frequency response of 40 Hz - 22 kHz (±3 dB), while the product page lists 40 Hz - 24 kHz. Sensitivity is 86 dB (500 Hz, 2.83 V/1 m) and impedance is 4 ohms nominal. Each panel measures 1,638 x 489 x 51 mm (H x W x D) and weighs 17 kg, and the shipping carton weighs 44 kg. Warranty is limited to 3 years for the original purchaser.

Engineering and use context

All three sections - mid/bass, tweeter and super tweeter - use aluminium foil adhered to a Mylar diaphragm, the arrangement Magnepan calls quasi-ribbon. An AC signal in the conductor foil reacts with a fixed array of magnet strips mounted behind the Mylar, and the diaphragm radiates as a dipole, forward and backward. Its tweeter sections are the tighter foil runs near one edge of the panel. Speakers of a pair carry the suffix -1 or -2 in the serial number, so the tweeters can sit on the outside or the inside of the pair.

On the nameplate, the AMPLIFIER terminal screws take bare wire up to 10 gauge or banana plugs, and spade lug adaptors are sold separately. A nickel banana jumper bridges the TWEETER/ATTENUATOR terminals. Two 1 ohm ceramic resistors are supplied to attenuate the tweeter section in place of this jumper, and Magnepan allows values up to 2 ohms. Fuses are 3AG fast-blow types of 4 A, with a maximum rating of 4 A, 250 V. Also in the carton are four T-feet with eight bolts, four long bolts with eight nylon washer spacers for a tilt of about 1 to 3 degrees, and an Allen wrench.

Fabric comes in black, grey, off-white or cherry white, with stiles in dark cherry, natural oak, or black, silver and gold aluminium. For the MG1.7x, red aluminium and black wood are added, and the circuit becomes a two-way design without the super tweeter, with cross-braces in the frame, copper-rich polypropylene capacitors and air-core coils wound at Magnepan.

Pairing

An amplifier able to produce at least 120 W per channel (RMS) into 4 ohms is required. Magnepan prefers powerful or high-current amplifiers and sets no upper power limit.

Alternatives

The MG2.7i is the next Magneplanar floorstanding model, with quasi-ribbon bass and midrange sections and a True Ribbon Tweeter.

Spezifikationen

  • Modellbezeichnung

    Magnepan 1.7i

  • Untere Grenzfrequenz +/- 3dB (Hz)

    40

  • Obere Grenzfrequenz +/- 3dB (Hz)

    24 000

  • Empfindlichkeit (dB at 1 W/1m)

    86

  • Impedanz (Ohms)

    4

  • Anforderungen an den Endverstärker (W)

    N/A

  • Verfügt über interne Verstärkung

    k. A.

  • Leistung der internen Verstärkung (W)

    N/A

  • Größe (sm)

    48.26 × 165.1 × 5.08

  • Gewicht (kg)

    N/A

  • Offizieller Link

Weitere Komponenten