Hifiverse

Standlautsprecher - Odeon Audio HELIX

Beschreibung, Bilder, technische Daten und Spezifikationen

Odeon Audio HELIX
Bildquelle - (c) Odeon Audio

The Helix is the smallest three-way horn loudspeaker from Odeon Audio, a maker based in Haltern am See, Germany. Odeon presents it as the beginning of a new era after its designs of 1992 and 2000, and the Helix replaces the Odeon No. 28/SE. Finishes are walnut root, tiger walnut, poplar, maple burl, white, palisander, walnut, black/gold and macassar.

Key specs that matter

Frequency range is 30 Hz - 26 kHz, sensitivity is 94 dB and impedance is 8 ohms. Crossover points are 450 Hz and 2.6 kHz. Each cabinet measures 1,175 x 480 x 525 mm (H x W x D) and weighs 51 kg. The tweeter is a 25 mm compression driver with ring radiator technology, an extra-light Mylar diaphragm and a 2.2 Tesla neodymium magnet, loaded by a 170 mm birch multiplex horn. Midrange comes from a handmade 130 mm GAP driver behind a 420 mm spherical wave horn, and bass from a 254 mm Audax paper woofer with an oversized ferrite magnet.

Engineering and use context

GAP builds the midrange driver with a die-cast aluminium basket, a 1.2 Tesla neodymium magnet and an ultra-light cellulose cone in hyperbolic NAWI (non-unwindable) form. Instead of a rubber surround, the multiple folded edge of the cone acts as the surround. A diffraction plug replaces the dust dome and reduces the moving mass to 2 g. Its spherical wave horn is made of layered blocks of birch plywood, while Odeon describes the tweeter horn as a mechanical amplifier that relieves the tweeter. The Audax woofer uses the same technology as the woofers of the larger Semper and Carnegie.

Inside the two-part cabinet, multiplex is combined with a special MDF. Compared with the No. 28/SE, the new bass cabinet holds more volume, its asymmetrical shape prevents standing waves, and less damping material is used. All drivers sit exactly on one axis. Like every Odeon floorstanding loudspeaker, the Helix has a downward bass reflex system, with the reflex tunnel pointing to the base plate.

Crossover components are selected to a maximum deviation of 1%, with WIMA film capacitors, New Old Stock bridge capacitors and Mundorf flat and round wire coils. Rather than on Pertinax boards, the crossovers are wired by hand, soldered point to point and mechanically secured. Internal wiring is German OFC copper, and the high-frequency section uses thin 7N monocrystalline solid-core copper with Teflon insulation. WBT Nextgen terminals of gold-plated pure copper are mounted on acrylic plates that also carry the crossovers.

Pairing

Odeon specifies the Helix for solid-state and tube amplifiers, down to low-power triode designs such as the 300B. An amplifier rated for an 8 ohm load is required.

Alternatives

The Odeon Semper is the next three-way horn model up, with a 330 mm woofer, a 500 mm midrange horn and a rated 96 dB sensitivity.

Spezifikationen

  • Modellbezeichnung

    HELIX

  • Untere Grenzfrequenz +/- 3dB (Hz)

    30

  • Obere Grenzfrequenz +/- 3dB (Hz)

    26 000

  • Empfindlichkeit (dB at 1 W/1m)

    94

  • Impedanz (Ohms)

    8

  • Anforderungen an den Endverstärker (W)

    N/A

  • Verfügt über interne Verstärkung

    k. A.

  • Leistung der internen Verstärkung (W)

    N/A

  • Größe (sm)

    117.5 x 48 x 52.5

  • Gewicht (kg)

    N/A

  • Offizieller Link

Weitere Komponenten