Hifiverse

Vorverstärker - Allnic Audio L-8000 DHT

Beschreibung, Bilder, technische Daten und Spezifikationen

Allnic Audio L-8000 DHT
Bildquelle - (c) Allnic Audio

The Allnic Audio L-8000 DHT is a stereo line-level tube preamplifier made by the Korean firm Allnic Audio, announced at the end of 2017 with a US price of USD 21,900 and later listed at USD 22,900. Allnic describes its predecessor, the L-5000 DHT, as the first commercially produced preamplifier with directly heated triodes in every signal stage, and the L-8000 DHT keeps that principle. Every amplification stage uses a directly heated triode rather than following an indirectly heated tube, and the output is coupled through transformers instead of capacitors. Silver and black finishes were offered at launch.

Key specs that matter

Connections cover three RCA and two XLR inputs, each with a 10 kOhm input impedance, plus one RCA and two XLR outputs. Voltage gain is 18 dB, and the output impedance is a constant 120 Ohm. The maximum non-clipping output reaches 20 V RMS. The response runs flat from 20 Hz to 20 kHz and extends from 16 Hz to 75 kHz at the -3 dB points. Distortion is quoted at 0.06% THD with 0.3 V out and 0.16% with 1.0 V out, while unweighted noise sits 90 dB below the signal level. Physically, the case is 430 mm wide, 351 mm deep and 211 mm high, it weighs 19.1 kg, and power consumption is 30 W.

Engineering and use context

Eight tubes of four types are used, two of each. A 3A/110A directly heated triode forms the first gain stage and a 3A/109B the second output stage, both types made by STC in Britain between 1925 and 1945. Voltage regulation is also done with tubes, where a 7233 acts as the regulator and a 5654 as the voltage error detector. The line output transformers are wound on Permalloy, a nickel-iron core alloy, and no negative feedback is applied anywhere in the class A circuit. Volume is set by a 61-step constant-impedance attenuator with silver contacts and relay switching, operated from a metal remote control. A soft-start circuit brings the supply up gradually, and Allnic's patented Absorb Gel dampers are fitted to keep vibration away from the signal tubes and cut microphonic noise. Yellow bias meters sit on the front panel.

Pairing

The low, constant output impedance and high output swing let the L-8000 DHT drive long balanced cable runs into tube or solid-state power amplifiers whose input impedance is modest. Bi-amping or a pair of monoblocks fed over XLR is easy to arrange, because both balanced outputs are live at once. Vinyl replay requires an external phono preamplifier, because the unit offers line inputs only.

Alternatives

The Allnic Audio L-7000 is a dual-mono line preamplifier from the same range that uses 300B tubes as voltage regulators in its power supply.

Spezifikationen

  • Modellbezeichnung

    L-8000 DHT

  • Analogeingänge (symmetrisch)

    2

  • Analogeingänge (unsymmetrisch)

    3

  • Analogausgänge (symmetrisch)

    2

  • Analogausgänge (unsymmetrisch)

    1

  • Verstärkung (dBu)

    18

  • Eingangsempfindlichkeit (mV)

    N/A

  • Ausgangsspannung (V)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    10 000

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    10 000

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Ausgangspegel (symmetrisch) (dBu)

    120

  • Maximaler Ausgangspegel (unsymmetrisch) (dBu)

    120

  • Regelbereich der Lautstärke (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    16

  • Obere Grenzfrequenz +/- 3dB (Hz)

    75 000

  • Signal-Rausch-Abstand (SNR, unbewertet) (dB)

    90

  • Klirrfaktor + Rauschen (THD+N) (%)

    0.06 at 0.3V, 0.16 at 1.0V

  • Abmessungen (mm)

    430 x 351 x 211

  • Gewicht (kg)

    19.1

  • Offizieller Link