Hifiverse

Endstufen Stereo - Accuphase P-7500

Beschreibung, Bilder, technische Daten und Spezifikationen

Accuphase P-7500
Bildquelle - (c) Accuphase

The P-7500 is the flagship Class AB stereo power amplifier from Accuphase of Japan. It descends from the P-300 of 1973 and is the 4th generation model since the P-7000 of 2003. Compared with the P-7300, rated at 125 W into 8 ohms and 48.6 kg, it has the same unit dimensions and slightly higher mass.

Key specs that matter

Rated output (20 Hz - 20 kHz, 0.05%) is 300 W into 8 ohms, 600 W into 4 ohms and 900 W into 2 ohms, the 4 and 2 ohm figures limited to music signals. In bridged connection both channels drive one speaker for 1,200 W into 8 ohms and 1,800 W into 4 ohms. THD is 0.03% (4 to 16 ohms) and 0.05% (2 ohms), and IMD is 0.01%. Frequency response is 20 Hz - 20 kHz (+0, -0.2 dB) at rated output and 0.5 Hz - 160 kHz (+0, -3.0 dB) at 1 W. Damping factor is 1,000 or greater. S/N is 130 dB with the gain switch at MAX and 135 dB at -12 dB. Input impedance is 40 kohms balanced and 20 kohms line, with 1.95 V input sensitivity for rated output. Power consumption is 142 W idle, 450 W per IEC 62368-1 and 0.3 W in standby. Maximum dimensions are 465 x 238 x 515 mm (W x H x D), and net mass is 49.0 kg.

Engineering and use context

Each channel has a 10-parallel push-pull output stage of bipolar power transistors rated 150 W and 15 A. A three-stage Darlington configuration drives the final stage through a two-stage drive circuit, which minimises the influence of speaker counter-electromotive forces on the output stage. Gain is distributed as 22 dB (12.6x) in the signal input section and 6 dB (2x) in the power amplification section. Accuphase quotes actual output noise of 16 µV against 18 µV for the P-7300, 11% lower. Its balanced input follows the instrumentation amplifier principle with equal input impedance on the + and - sides. Two MCS+ circuits run in parallel in the voltage amplification stage, and current feedback is used for phase characteristics at high frequencies. Balanced remote sensing feeds back signal and GND from the speaker terminals.

Inside is a mono-block construction with separate left and right power amplifier units, a large toroidal transformer and two 60,000 µF filtering capacitors. Speaker protection uses MOS-FET switches with 1.6 mOhm on-resistance, photo-coupler short-circuit detection and two temperature sensors per heatsink. Gain switching works at the input amplifier section, not with an attenuator.

Pairing

A preamplifier with balanced XLR or RCA line outputs is required, and the front gain selector offers MAX, -3, -6 and -12 dB. Two pairs of speaker terminals allow bi-wiring, and two units allow bi-amping or bridged mode.

Alternatives

The P-4600 is the smaller Class AB stereo power amplifier in the Accuphase range.

Spezifikationen

  • Modellbezeichnung

    P-7500

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    N/A

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    300

  • Ausgangsleistung (4Ω) (W)

    600

  • Verstärkung (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Obere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Signal-Rausch-Abstand (dB)

    N/A

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    N/A

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    1000

  • Abmessungen (mm)

    465 x 238 x 515

  • Gewicht (kg)

    49.0

  • Offizieller Link

Weitere Komponenten