Hifiverse

Phonostages - TEAC PE-505

Description, images, technical data and specifications

TEAC PE-505
Image source - (c) TEAC

The PE-505 is a phono equalizer amplifier from TEAC's Reference 500 series, with fully balanced circuitry from the head amplifier to the output buffer. It accepts moving magnet and moving coil cartridges, and its front panel carries a gauge used for load measurement and subsonic detection. TEAC USA sells it for USD 2,499.99 with a black or silver front.

Key specs that matter

Inputs are one RCA pair for MM or MC and one XLR pair for MC only. MM input impedance is 47 kohms with load capacitance of 0, 100, 220 or 330 pF. MC load is 10, 22, 47, 100, 220, 470 or 1,000 ohms on either input, switchable from the Settings. Gain is 34 dB (MM) and 54 dB (MC) in GAIN LOW, and 46 dB and 66 dB in GAIN HIGH. Maximum input level is 150 mV for MM and 16 mV for MC (THD 0.1%, GAIN Low). THD is 0.002% on MM and 0.02% on MC (rated output, 1 kHz, GAIN Low). S/N ratio reaches 106 dB on the RCA MM input and 86 dB on the XLR MC input, and residual noise is 10, 65 and 85 µV for MM, RCA MC and XLR MC (input short, IHF-A). RIAA deviation is ±0.05 dB (20 Hz - 20 kHz), and channel separation is -90 dB or better (MM, 10 kHz). Outputs are RCA at 2 Vrms (63 ohms) and XLR at 4 Vrms (126 ohms). Power consumption is 14 W, dimensions are 290 x 84.5 x 252.5 mm (W x H x D), and weight is 4.5 kg.

Engineering and use context

All stages run in balanced form. Even a signal on the RCA input is converted to differential mode right after the input terminals. Equalisation is applied on the differential cartridge output, where the hot and cold outputs are cross-multiplied so that errors between them are absorbed. A newly developed NF-type equalizing amplifier sets the RIAA curve. Besides RIAA, TEAC supports the individual DECCA and COLUMBIA curves issued before RIAA was defined in 1955, and a MONO function mixes the left and right channels.

Pressing the MEASURE key on the front panel shows on the gauge the total load resistance, cable resistance included. The same gauge indicates subsonic signals below 6 Hz, and a subsonic filter (17 Hz, -24 dB/octave) removes them. In the DEMAG position the iron cores of an MC cartridge and a step-up transformer are demagnetised while a record plays for as little as 30 seconds. A GND terminal and 3-position pin-point feet complete the chassis.

Pairing

A tonearm cable with XLR termination is required for the balanced MC input. A preamplifier or integrated amplifier with balanced line inputs is required for the XLR output. The RCA output connects to an unbalanced line-level input.

Alternatives

TEAC has no other phono preamplifier in its range, so there is no direct alternative within the brand.

Specifications

  • Model name

    PE-505

  • Inputs (balanced)

    1

  • Inputs (single-ended)

    1

  • MC current-sensing input impedance (Ω)

    10, 22, 47, 100, 220, 470, 1000

  • MM/MC voltage input impedance (Ω)

    N/A

  • Output impedance (Ω)

    N/A

  • Gain (dB)

    46 / 66

  • Playback EQ curves accuracy (dB)

    N/A

  • Frequency response low +/- 3dB (Hz)

    N/A

  • Frequency response high +/- 3dB (Hz)

    N/A

  • Total Harmonic Distortion + Noise (%)

    0.002 (MM RCA) + 0.02 (MC XLR) + 0.02 (MC RCA)

  • Dimensions (mm)

    290 × 84.5 × 252.5

  • Weight (kg)

    4.5

  • Official link