Hifiverse

Cartridges - Audio-Technica AT33xMLB

Description, images, technical data and specifications

Audio-Technica AT33xMLB
Image source - (c) Audio-Technica

The AT33xMLB is the flagship stereo model of the AT33x series of dual moving coil (MC) cartridges from Audio-Technica of Japan. Five models make up the series, three stereo and two mono, and it is the first full model change of the AT33 line since 2014. Audio-Technica released the AT33xMLB in October 2025 at USD 899. This version pairs a microlinear nude stylus with a solid boron tapered cantilever, and every cartridge is hand-crafted in Japan. Its stylus is not user-replaceable, and worn units go through the paid Audio-Technica exchange programme.

Key specs that matter

Stylus is a 55.9 x 3.0 µm nude microlinear on a solid boron tapered cantilever. Output voltage is 0.42 mV (1 kHz, 5 cm/s), with channel separation of 27 dB (1 kHz) and output balance of 1.0 dB (1 kHz). Frequency response is 20 Hz - 45 kHz. Coil impedance is 12 ohms (1 kHz), DC resistance 12 ohms and coil inductance 26 µH (1 kHz). Recommended load is 100 ohms or more with a head amplifier. Static compliance is 19 x 10-6 cm/dyne and dynamic compliance 6 x 10-6 cm/dyne (100 Hz). Tracking force is 1.8 - 2.2 g (2.0 g standard), and vertical tracking angle is 19°. It measures 16.0 x 16.6 x 26.1 mm (H x W x D) and weighs 10.1 g.

Engineering and use context

Boron has a high vibration propagation speed, and the solid boron cantilever tapers toward the tip to lower moving mass at the stylus end. At the cantilever support Audio-Technica uses a stepped pipe structure - the joint of cantilever and armature is a double structure that raises rigidity and suppresses unwanted resonance. With its small radius the microlinear tip keeps distortion low on the inner grooves of a record. Its line-contact shape is maintained until the stylus is close to worn out.

Independent left and right coils form the dual moving coil structure, wound with PCOCC (Pure Copper by Ohno Continuous Casting) wire. A neodymium magnet and a permendur yoke create a strong field in the magnetic gap. Each AT33x model has a newly developed suspension and rubber damper, with dynamic compliance slightly lower than in other Audio-Technica cartridges, for use with a variety of tonearms. Die-cast zinc forms the base, the first such use by Audio-Technica, and aluminium and a high-rigidity polymer complete the composite body. Gold plating on the terminal pins is thicker than on earlier models to lower contact resistance, and threaded M2.6 holes allow direct mounting on integrated tonearms.

Pairing

An MC phono stage or a head amplifier with a load of 100 ohms or more is required. A step-up transformer into an MM input is the other option.

Alternatives

The AT33xMLD has the same microlinear nude stylus on a duralumin tapered pipe cantilever.

Specifications

  • Model name

    AT33xMLB

  • Type

    MC

  • Stylus

    Nude Microlinear

  • Body

    Die-cast zinc, aluminum, and high-rigidity polymer

  • Cantilever

    Nude tapered boron

  • Coils

    N/A

  • Output voltage (mV@5cm/sec)

    0.42

  • Frequency response low +/- 3dB (Hz)

    20

  • Frequency response high +/- 3dB (Hz)

    45 000

  • Internal impedance (Ohm)

    N/A

  • Channel separation (dB / 1,000 Hz)

    27

  • Compliance (×10-6cm/dyne at 100Hz)

    6

  • Recommended load (Ohm)

    ≥ 100

  • Recommended tonearms

    N/A

  • Weight (g)

    10.1

  • Official link