Hifiverse

DACs — Cayin RU3

Description, images, technical data and specifications

Cayin RU3
Image source - (c) Cayin

The RU3 is a portable USB DAC/headphone amplifier dongle from Cayin. Its unibody chassis is CNC-milled from aerospace-grade aluminium alloy, with an anodised finish and laser-engraved detailing on the rear panel. It was listed at USD 99 in black, light cyan or purple, and an anti-interference Type-C cable with high-density shielding is included.

Key specs that matter

Conversion uses a single ESS ES9069Q DAC in a dual-channel design, based on the ESS HyperStream IV Dual DAC architecture and SABRE HiFi technology. Supported formats are PCM up to 768 kHz/32-bit and native DSD512. Outputs are a 3.5 mm single-ended and a 4.4 mm balanced socket, both usable as phone or line outputs. Output power is 180 mW + 180 mW (32 ohms) single-ended and 560 mW + 560 mW (32 ohms) balanced, measured in Hyper mode. The chassis measures 60 x 25.4 x 11 mm and weighs 24 g.

Engineering and use context

Two TI OPA1602 op-amps are used for I/V conversion and line driving, and two SGM8262 low-noise amplifiers complete a fully balanced quad-drive design. Each channel has its own op-amp, and Cayin adds an independent LDO power system and a low-phase-noise crystal oscillator. USB audio runs on the SPV5068 processor, a RISC-V dual-core audio architecture.

Switchable UAC 1.0 and UAC 2.0 modes give compatibility with Android, iOS, Windows and macOS. In UAC 1.0 mode the RU3 also connects to the PS5, the Nintendo Switch and other consoles. Two power modes are provided - HYP (Hyper) for up to the full output, and STD (Standard) for a lower power load on mobile devices and less heat. High and low gain modes are selectable for different headphone impedances, and in LO (Line Out) mode both sockets connect to external amplifiers.

On the body is a 24 mm IPS colour display for decoding status and system settings, with four UI themes, and multifunction buttons give hardware control. Through the companion app the RU3 offers 100-step volume control, 20-step channel balance, five digital filters, two gain levels and a 10-band lossless EQ with saved custom profiles. Firmware v1.0.3 added a parametric equaliser (PEQ).

Pairing

A USB-C source with UAC 1.0 or UAC 2.0 support is required. Headphones with a 3.5 mm or 4.4 mm balanced plug connect directly. In LO mode either socket drives an external headphone amplifier or powered speakers.

Alternatives

The RU7 is another portable USB DAC/headphone amplifier dongle in Cayin's range.

Specifications

  • Model name

    RU3

  • Conversion type

    N/A

  • Engine

    ES9069Q

  • DSD compatability

    Yes

  • Parameters

    up to 32 bit / 768 kHz and DSD512

  • Frequency response low +/- 3dB (Hz)

    N/A

  • Frequency response high +/- 3dB (Hz)

    N/A

  • Gain (dBu)

    N/A

  • Output Level (balanced) (V)

    N/A

  • Output Level (single-ended) (V)

    N/A

  • Input Impedance (balanced) (Ω)

    N/A

  • Input Impedance (single-ended) (Ω)

    N/A

  • Output Impedance (balanced) (Ω)

    N/A

  • Output Impedance (single-ended) (Ω)

    N/A

  • Analog outputs

    N/A

  • Signal to Noise Ratio (dB)

    N/A

  • Total Harmonic Distortion + Noise (% at 22 kHz)

    N/A

  • Dimensions (mm)

    N/A

  • Weight (kg)

    N/A

  • Official link