Hifiverse

DACs - Ayre Acoustics QA-9 Pro

Description, images, technical data and specifications

Ayre Acoustics QA-9 Pro
Image source - (c) Ayre Acoustics

QA-9 Pro is an analogue-to-digital converter (ADC), not a DAC, from Ayre Acoustics of Boulder, Colorado. It converts a line-level analogue signal into digital data for a computer or recorder, and Ayre names recording, mastering, archiving and product development as its uses. The QA-9 exists in two versions covered by one owner's manual - the standard unit with USB and AES/EBU outputs, and the Pro, which adds DSD and word clock outputs for the studio.

Key specs that matter

Input impedance is 2 Mohm balanced (1 Mohm per phase). Analogue input sensitivity is 10.0 V RMS at minimum gain and 0.75 V RMS at maximum gain. USB audio output is 44.1, 48, 88.2, 96, 176.4 and 192 kHz at 24 bits in Class 2, and 44.1 to 96 kHz in Class 1. AES/EBU output covers the same six rates at 24 bits on a 110 ohm transformer-isolated XLR. DSD output is SDIF-2 at 64x, 128x and 256x and SDIF-3 at 64x and 128x, on 75 ohm transformer-isolated BNCs. Frequency response is DC - 20 kHz at 44.1 kHz, DC - 66 kHz at 192 kHz and DC - 80 kHz with DSD256. Power consumption is 25 W. Dimensions are 215 x 305 x 75 mm (W x D x H), and weight is 2.3 kg.

Engineering and use context

Ayre uses a discrete, fully balanced, zero-feedback analogue circuit with its variable gain stage and Equilock circuitry for the active gain devices. Conversion is based on the Arda AT1201. Input sensitivity is set only with the front knob, in twelve steps of 2.0 dB, so the full dynamic range of each source reaches the digital recording. Vertical bar-graph meters on either side of the display show the digital level of each channel, and the top red segment indicates clipping with a ten-second hold.

Inputs are balanced XLR, and single-ended-to-balanced adapters are included. Opto-couplers give full electrical isolation between the computer and the music system. Rear toggle switches set the AES/EBU sample rate, display brightness and the PCM digital filter, which has two algorithms - Listen, with greater accuracy in the time domain, and Measure, with greater accuracy in the frequency domain. Whenever the USB output is active, the AES/EBU output is disabled.

On the Pro, the DSD output uses Sony's single-bit format on three BNC connectors, and enabling it overrides the word clock settings. Its word clock outputs carry TTL-level signals taken directly from the master clock inside the converter, and digital studio equipment can be slaved to it.

Pairing

A phono stage, tape deck or other line-level source with balanced outputs is required, or a single-ended one through the supplied adapters. Archiving software such as Vinyl Studio or Pure Vinyl, or recording software such as Audacity or Pro Tools, runs on the computer.

Alternatives

The standard Ayre QA-9 is the same converter without the DSD and word clock outputs.

Specifications

  • Model name

    QA-9 Pro

  • Conversion type

    N/A

  • Engine

    N/A

  • DSD compatability

    Yes

  • Parameters

    up to 24 bit / 192 kHz and DSD256

  • Frequency response low +/- 3dB (Hz)

    N/A

  • Frequency response high +/- 3dB (Hz)

    80 000

  • Gain (dBu)

    N/A

  • Output Level (balanced) (V)

    N/A

  • Output Level (single-ended) (V)

    N/A

  • Input Impedance (balanced) (Ω)

    2 000 000

  • Input Impedance (single-ended) (Ω)

    N/A

  • Output Impedance (balanced) (Ω)

    N/A

  • Output Impedance (single-ended) (Ω)

    N/A

  • Analog outputs

    N/A

  • Signal to Noise Ratio (dB)

    N/A

  • Total Harmonic Distortion + Noise (% at 22 kHz)

    N/A

  • Dimensions (mm)

    215 x 290 x 75

  • Weight (kg)

    2.3

  • Official link