Hifiverse

DACs — Mola Mola DAC

Description, images, technical data and specifications

Mola Mola DAC
Image source - (c) Mola Mola

The Mola Mola DAC is an optional discrete digital-to-analogue converter board for the Makua preamplifier and the Kula integrated amplifier from Mola Mola of the Netherlands. It is not a standalone component. Mola Mola developed its circuits and digital algorithms entirely in house rather than using a converter chip, and states that the best DAC chips claim no better than 22 bits of dynamic range and 20 bits of linearity. According to the company, the DAC section is identical to the stand-alone Tambaqui. European prices for the board were around EUR 6,500.

Key specs that matter

Inputs are AES/EBU on XLR, optical Toslink, USB type B, Bluetooth with SBC, AAC, aptX and LDAC, and Ethernet with Roon Ready certification. PCM is accepted up to 384 kHz/32-bit, with rates above 192 kHz and word lengths above 24 bits via USB and Roon only. DoP and native DSD are supported up to quad speed, also via USB and Roon only. Full-scale output level is 20 dBu and signal-to-noise ratio is 130 dB. THD and IMD are not measurable, with an estimated -140 dB. Bandwidth extends up to 80 kHz with an apodizing response. Integrated jitter is below 1 ps from 10 Hz upwards and below 300 fs from 1 kHz upwards, and jitter rejection is more than 80 dB at 1 Hz after 20 seconds of lock.

Engineering and use context

Physically the converter is a two-board stack that fits one of the option slots of the host chassis. On the first board, all incoming digital audio is upsampled to 3.125 MHz/32-bit and converted to noise-shaped PWM. Two mono DACs sit on the second board, each with a discrete 32-stage FIR DAC and a single-stage 4th-order filtering I/V converter that converts the PWM to analogue. Mola Mola states that distortion remains below the noise floor even for full-scale signals.

For jitter Mola Mola uses its own asynchronous upsampling algorithm. Its input frequency measurement slows down until, after a few seconds of lock, the frequency ratio measurement is frozen. From then on, frequency stability depends only on the internal clock, a laboratory-grade 100 MHz SC-cut oscillator.

Inside a Makua or Kula, all inputs can be routed through the optional processor boards, and the Kula becomes Roon Ready once the DAC option is installed. The Makua chassis has room for both the DAC and the optional phono stage.

Pairing

A Makua preamplifier or a Kula integrated amplifier is required as the host. With a Makua, Mola Mola's Kaluga monoblocks or Perca stereo power amplifier are the in-house power amplifiers.

Alternatives

The Mola Mola Tambaqui is the stand-alone DAC, 200 mm wide, with headphone outputs on 6.3 mm and balanced 4-pin XLR, I2S over HDMI and lossless digital volume control.

Specifications

  • Model name

    DAC

  • Conversion type

    N/A

  • Engine

    N/A

  • DSD compatability

    Yes

  • Parameters

    up to 192/24 (above and DSD256 - only via USB and Roon)

  • Frequency response low +/- 3dB (Hz)

    N/A

  • Frequency response high +/- 3dB (Hz)

    N/A

  • Gain (dBu)

    N/A

  • Output Level (balanced) (V)

    N/A

  • Output Level (single-ended) (V)

    N/A

  • Input Impedance (balanced) (Ω)

    N/A

  • Input Impedance (single-ended) (Ω)

    N/A

  • Output Impedance (balanced) (Ω)

    N/A

  • Output Impedance (single-ended) (Ω)

    N/A

  • Analog outputs

    N/A

  • Signal to Noise Ratio (dB)

    130

  • Total Harmonic Distortion + Noise (% at 22 kHz)

    N/A

  • Dimensions (mm)

    N/A

  • Weight (kg)

    N/A

  • Official link