Hifiverse

DACs - Imersiv D-1 HDR-A

Description, images, technical data and specifications

Imersiv D-1 HDR-A
Image source - (c) Imersiv

The D-1 HDR-A is a stereo DAC from imersiv, a Millennia company based in Diamond Springs, California, and founded by John La Grou, who started the pro-audio maker Millennia Media in 1990. Its HDR-A, or High Dynamic Range Audio, is a multiple-path conversion architecture that took over 10 years of development from an idea of 2013. The D-1 was introduced in autumn 2023 at the AES convention in New York at USD 12,000.

Key specs that matter

Supported formats are 32 kHz to 384 kHz at up to 32 bit, plus DSD 1x, 2x and 4x. Digital inputs are one USB-B (32-bit), one AES on XLR, three S/PDIF on BNC and one Toslink, with Dante as an option. The XLR analogue output gives +22 dBu differential-balanced (9.75 V RMS) maximum with zero inter-sample overs and 1.8 ohms output impedance. Frequency response is 20 Hz - 20 kHz (±0.1 dB). THD+N is 0.0002% at 1 kHz (22 kHz BW) and 0.0005% at 20 kHz (80 kHz BW), both at +22 dBu. Self-noise is -146 dBu unweighted (20 Hz - 22 kHz), dynamic range is 168 dB (28 bits), and crosstalk is better than -120 dB at 1 kHz. Its headphone output drives 32 to 600 ohms at up to 2.8 W. Level control works in 0.1 or 1.0 dB steps over a 154 dB range (-130 to +24 dB). The chassis measures 218 x 414 x 81 mm (W x D x H) and weighs 3.4 kg.

Engineering and use context

Inside, the D-1 has two signal paths, a high-path and a low-path. When the programme falls below about -40 dBFS, conversion moves to a different DAC core that converts at full MSB with lower THD+N, and imersiv quotes 40 nV of broadband noise. HDR-A is triple-patented and inherently differential-balanced. Wired in parallel with the XLR outputs, the RCA outputs are not performance-specified. A calibration cycle sends pilot tones on both paths while DSP adjusts the path levels until the cross-fade linearity error is below 0.005 dB, typically in about 30 seconds. Line and headphone outputs are calibrated separately, and calibration is repeated after any connected component or cable changes.

DSD arrives as DoP and is converted internally to 192 kHz PCM. A 10-gauge aluminium plate gives RF shielding between the digital and analogue boards, and power comes from a galvanically isolated external supply for 90 to 240 V, drawing 15 W nominal. Six digital filters, polarity flip and an output relay mute are provided, with a 256 x 64 OLED display and a 27-function IR remote. Three BNC to RCA adapters are included.

Pairing

A power amplifier or active monitors with balanced XLR inputs are required for full HDR-A performance. The level control allows direct connection without a preamplifier.

Alternatives

imersiv makes no other DAC, as the D-1 is the company's only product.

Specifications

  • Model name

    D-1 HDR-A

  • Conversion type

    N/A

  • Engine

    N/A

  • DSD compatability

    N/A

  • Parameters

    up to 32kHz / 384kHz

  • Frequency response low +/- 3dB (Hz)

    20

  • Frequency response high +/- 3dB (Hz)

    20 000

  • Gain (dBu)

    N/A

  • Output Level (balanced) (V)

    N/A

  • Output Level (single-ended) (V)

    N/A

  • Input Impedance (balanced) (Ω)

    N/A

  • Input Impedance (single-ended) (Ω)

    N/A

  • Output Impedance (balanced) (Ω)

    N/A

  • Output Impedance (single-ended) (Ω)

    N/A

  • Analog outputs

    N/A

  • Signal to Noise Ratio (dB)

    168

  • Total Harmonic Distortion + Noise (% at 22 kHz)

    0.0002

  • Dimensions (mm)

    N/A

  • Weight (kg)

    N/A

  • Official link

Related content