Hifiverse

DACs - Boulder 812

Description, images, technical data and specifications

Boulder 812
Image source - (c) Boulder

The 812 is a DAC, preamplifier and headphone amplifier in one chassis from Boulder Amplifiers of Louisville, Colorado, and it extends the company's 800 Series alongside the 866 integrated. It is Boulder's first headphone amplifier, and it can work as a preamp, a DAC, a headphone amp or any combination of the three. The US price is USD 9,250, and in Europe it sells for EUR 11,900.

Key specs that matter

Rear-panel connections are two pairs of balanced XLR analogue inputs, one pair of XLR preamplifier outputs, two Toslink optical inputs, a coaxial RCA S/PDIF input, USB-B, four USB host ports and Ethernet. Maximum input level is 6.0 Vrms at 100 kohm balanced, maximum output level is 14.0 Vrms from 100 ohm balanced, and maximum voltage gain is 19.4 dB. THD+N is 0.0017% (-95.5 dB) at 2 V output and 2 kHz. Clip-to-noise ratio is 116 dB. Frequency response is +0.00/-0.03 dB from 20 Hz to 5 kHz, with -3 dB points at 0.02 Hz and 250 kHz. Into 32 and 150 ohms the headphone section gives 200 mW, and into 600 ohms 80 mW. The chassis measures 305 x 305 x 89 mm, weighs 6.35 kg and draws 50 W maximum from 90-240 V mains.

Engineering and use context

Its digital section is based on the 866 DSP filter and DAC topology. Incoming data is asynchronously converted if necessary, up- and oversampled in Boulder's own software and DSP, and a multipole Bessel filter is used as the reconstruction filter. Streaming covers Roon endpoint, UPnP playback and AirPlay, and a software-enabled fixed DAC output is available on the XLR jacks. Balanced and unbalanced sources enter a true balanced, differential input stage. Level is set by a 100 dB optically encoded volume control in 1.0 dB steps, with input trim down to -25.0 dB in 0.5 dB steps.

A cascaded transistor array amplifier is dedicated only to the headphone jacks - 3.5 mm, 6.35 mm, 4-pin XLR and Pentaconn - mounted in a replaceable jack panel under a magnetic dust cover. When the preamplifier outputs are active, the headphone outputs are disabled, and an output exchange button switches between the two. Headphone sensitivity is set in the Boulder Controller app, and an RF remote is optional. Every circuit board and piece of metalwork is produced in house, including the machined volume knob and chassis.

Pairing

A power amplifier with balanced XLR inputs is required for speaker use. The matching power amplifier is the Boulder 861, which shares the same chassis size.

Alternatives

Boulder lists no other DAC in its current range.

Specifications

  • Model name

    812

  • Conversion type

    N/A

  • Engine

    N/A

  • DSD compatability

    N/A

  • Parameters

    N/A

  • Frequency response low +/- 3dB (Hz)

    0.02

  • Frequency response high +/- 3dB (Hz)

    250 000

  • Gain (dBu)

    N/A

  • Output Level (balanced) (V)

    N/A

  • Output Level (single-ended) (V)

    N/A

  • Input Impedance (balanced) (Ω)

    100 000

  • Input Impedance (single-ended) (Ω)

    N/A

  • Output Impedance (balanced) (Ω)

    100

  • Output Impedance (single-ended) (Ω)

    N/A

  • Analog outputs

    N/A

  • Signal to Noise Ratio (dB)

    116

  • Total Harmonic Distortion + Noise (% at 22 kHz)

    0.0017

  • Dimensions (mm)

    305 × 305 × 89

  • Weight (kg)

    6,35

  • Official link