Hifiverse

CD / SACD players and transports - Canor Audio CD 1.10

Description, images, technical data and specifications

Canor Audio CD 1.10
Image source - (c) Canor Audio

The CD 1.10 is a tube CD player and DAC from Canor, the Slovak manufacturer of tube electronics based in Prešov. It sat at the top of Canor's CD players, retains the large matrix display of its predecessor, the CD2 VR+, and shares its styling with Canor's amplifiers. Apart from disc playback it works as a standalone DAC with coaxial, optical and USB inputs.

Key specs that matter

Each channel has its own 24-bit/192 kHz DAC. Supported formats are PCM from 44.1 to 192 kHz and DSD64, DSD128 and DSD256. Frequency range is 20 Hz - 20 kHz (±0.8 dB), THD is below 0.005% (1 kHz) and signal-to-noise ratio is above 102 dB. Analogue outputs are RCA at 2.5 V and XLR at 5 V, with output impedance below 100 ohms, and digital outputs are coaxial and optical. The tube complement is two 12AX7, two 6922 and one 6CA4. Dimensions are 435 x 170 x 420 mm (W x H x D), and weight is 15 kg.

Engineering and use context

Both DAC chips are galvanically isolated from the digital section, away from the noise of the transport and receiver circuits. After conversion, super-symmetrical passive filters with a steep slope remove out-of-band products. In the analogue output stage the tubes operate in pure class A with automatic bias and cathode feedback, and a 6CA4 tube rectifier is used in the high-voltage supply. Its disc drawer runs on bearing-supported rails. Canor's own CMT technology is used for the circuit boards, and chassis parts are made by the company's PCD milling process.

An oversized power transformer is specified for low stray magnetic field and low noise. Canor's Voltage Stabilization Circuit monitors the mains voltage in real time and switches between several primary windings of the transformer. It holds the tube heater and anode supplies within specification and extends tube life. Two digital filters are selectable from the front panel. On the front, the orange matrix display follows the layout used on Canor's amplifiers.

Pairing

The XLR output requires a preamplifier or integrated amplifier with balanced inputs, Canor's tube integrated amplifiers among them. A computer connects to the USB input. The coaxial and optical outputs connect the transport to an external DAC.

Alternatives

The CD 2.10 is Canor's smaller tube CD player and DAC.

Specifications

  • Model name

    CD 1.10

  • Transport

    Yes

  • Player

    Yes

  • SACD support

    N/A

  • Engine

    N/A

  • Frequency response low +/- 3dB (for CD) (Hz)

    20

  • Frequency response high +/- 3dB (for CD) (Hz)

    20 000

  • Frequency response low +/- 3dB (for SACD) (Hz)

    N/A

  • Frequency response high +/- 3dB (for SACD) (Hz)

    N/A

  • Gain (dBu)

    N/A

  • Output Level (balanced) (V)

    5

  • Output Level (single-ended) (V)

    2.5

  • Input Impedance (balanced) (Ω)

    N/A

  • Input Impedance (single-ended) (Ω)

    N/A

  • Output Impedance (balanced) (Ω)

    <100

  • Output Impedance (single-ended) (Ω)

    <100

  • Dynamic range (for CD) (dB)

    N/A

  • Dynamic range (for SACD) (dB)

    N/A

  • Signal to Noise Ratio (for CD) (dB)

    >102

  • Signal to Noise Ratio (for SACD) (dB)

    N/A

  • Total Harmonic Distortion + Noise (for CD) (%)

    <0,005

  • Total Harmonic Distortion + Noise (for SACD) (%)

    N/A

  • Dimensions (mm)

    435 x 170 x 420

  • Weight (kg)

    15

  • Official link

More components