Hifiverse

Headphones amplifiers - Pass Labs HPA-1c

Description, images, technical data and specifications

Pass Labs HPA-1c
Image source - (c) Pass Labs

The HPA-1c is a headphone amplifier and line-level preamplifier from Pass Laboratories of Auburn, California. It updates the HPA-1 and keeps the core amplifier circuit of the original. Pass made the changes because several components had reached end of life - the power supply was upgraded, the circuit board grounding was improved and local regulation was added to the servo circuitry. Pass quotes an improvement of about 10 dB in overall noise performance.

Key specs that matter

Gain is 8 dB, and frequency response is 10 Hz - 100 kHz (-1 dB). Output power is 3500 mW into 20 ohms and 200 mW into 300 ohms, and Pass also states up to 2 W into 32 ohms. THD+N is below 0.005% at 1 V output. Input impedance is 50 kohms, output impedance is below 2 ohms, and headphone loads from 15 to 600 ohms are supported. Power consumption is 23 W. Dimensions are 279 x 343 x 102 mm (W x D x H), and weight is 6.4 kg. Inputs are two RCA pairs, and outputs are a locking 6.35 mm headphone jack and one switchable RCA preamplifier output.

Engineering and use context

Pass Labs designed the HPA-1 as a power amplifier rather than a typical headphone amplifier, so that it can drive low-impedance planar magnetic headphones. Its circuits are low-feedback, wide-bandwidth discrete designs with a JFET input stage and a direct-coupled MOSFET output stage biased into Class A. A custom low-noise toroidal transformer has a Faraday shield between the windings and a mu-metal shield around its circumference. The audio circuits have a discrete regulated power supply.

On the front panel the headphone jack is a Neutrik locking connector with an isolated signal ground and silver contacts rated at 10 A. Volume is set by a rotary knob on an ALPS potentiometer, and three pushbuttons select the inputs or engage the preamplifier output. Only one output, headphone or preamplifier, is active at a time. The preamplifier output drives a power amplifier load of 10 kohms or higher.

At power-on the unit stays muted for 20 seconds while the circuitry stabilises. It is designed to remain switched on and reaches optimum performance about one hour after turn-on. After a power loss it returns to the last input and function. The power switch and fuse are on the rear panel, and the casework is brushed aluminium.

Pairing

Headphones with a 6.35 mm plug connect directly, dynamic and planar magnetic models alike. As a preamplifier it requires a power amplifier with an input impedance of 10 kohms or more. Sources with RCA line outputs connect to the two inputs.

Alternatives

The HPA-1 is the earlier Pass Labs headphone amplifier, with the same core circuit and the previous power supply.

Specifications

  • Model name

    HPA-1c

  • Maximum Power, 32 Ohms (mW RMS per channel)

    N/A

  • Maximum Power, 50 Ohms (mW RMS per channel)

    N/A

  • Maximum Power, 300 Ohms (mW RMS per channel)

    200

  • Maximum Power, 600 Ohms (mW RMS per channel)

    N/A

  • Frequency response low +/- 3dB (Hz)

    10

  • Frequency response high +/- 3dB (Hz)

    100000

  • Gain (dBu)

    8

  • THD (% at 1V RMS, 300 ohms)

    N/A

  • Signal to Noise Ratio (dB)

    0.05

  • IMD (%, CCIR, 300 Ohms)

    N/A

  • Crosstalk (dB, 20Hz-20KHz, 300 Ohms)

    N/A

  • Output Impedance (Ohms)

    2

  • Dimensions (mm)

    N/A

  • Weight (kg)

    N/A

  • Official link

Related content