Hifiverse

Headphones amplifiers - FiiO CLASS A

Description, images, technical data and specifications

FiiO CLASS A
Image source - (c) FiiO

FiiO, the Chinese electronics company, built the CLASS A as a desktop unit that works both as a headphone amplifier and as a preamplifier. It was released in September 2026 at USD 379.99 in black or silver, and its circuit is fully discrete, assembled from individual transistors, resistors and capacitors instead of an integrated amplifier chip.

Key specs that matter

Three headphone outputs sit on the front panel - a 6.35 mm single-ended jack, a 4.4 mm balanced socket and a 4-pin XLR. From the balanced outputs FiiO rates 4,000 mW per channel into 32 ohms, 2,000 mW into 16 ohms and 1,360 mW into 300 ohms. The single-ended jack gives 2,850 mW per channel into 32 ohms and 350 mW into 300 ohms. Sources connect through 3.5 mm, RCA, 4.4 mm balanced or XLR inputs, and RCA plus XLR line outputs pass the signal on. FiiO specifies an output impedance of 1 ohm and a 121 dB signal-to-noise figure. Five gain steps run from Low to Ultra High, and separate bass and treble controls give 10 dB of boost or cut. The case measures 213 x 239 x 67 mm and the unit weighs 3.5 kg.

Engineering and use context

The amplifier is fully balanced and differential, and each channel has its own positive and negative signal paths. The output devices are Toshiba matched-pair and complementary audio transistors alongside Sanken parts, and the quiescent current of every unit is set by hand at the factory. Power comes from a custom 60 W toroidal transformer feeding a 20,000 uF capacitor bank. The name needs a qualification that FiiO itself has given - headphones of 60 ohms and above run entirely in Class A, while with low-impedance loads the stage stays in Class A only up to roughly 140 mW at 16 ohms and a little over 500 mW at 32 ohms, then moves into Class AB, and this transition cannot be switched off. Protection covers DC at the output, input overcurrent, overvoltage, output overload and overheating of both the amplifier and the transformer. A pair of 12 V trigger sockets, one in and one out, lets the unit power up in sync with the rest of a system, and a USB-C port is used for firmware updates.

Pairing

The CLASS A has no digital input, so it needs an external DAC, streamer or player with analogue outputs, ideally balanced to use the XLR or 4.4 mm path end to end. The power reserve suits inefficient planar magnetic designs and dynamic headphones of 300 ohms or more, while sensitive in-ear monitors call for the lowest gain step. With the line outputs it can also act as a preamplifier for powered speakers or a separate power amplifier.

Alternatives

For portable use FiiO offers the SnowSky Retro Nano, a much smaller headphone amplifier.

Specifications

  • Model name

    CLASS A

  • Maximum Power, 32 Ohms (mW RMS per channel)

    2850 + 2850

  • Maximum Power, 50 Ohms (mW RMS per channel)

    350 + 350

  • Maximum Power, 300 Ohms (mW RMS per channel)

    N/A

  • Maximum Power, 600 Ohms (mW RMS per channel)

    N/A

  • Frequency response low +/- 3dB (Hz)

    20

  • Frequency response high +/- 3dB (Hz)

    95 000

  • Gain (dBu)

    N/A

  • THD (% at 1V RMS, 300 ohms)

    0.0006

  • Signal to Noise Ratio (dB)

    121

  • IMD (%, CCIR, 300 Ohms)

    N/A

  • Crosstalk (dB, 20Hz-20KHz, 300 Ohms)

    67

  • Output Impedance (Ohms)

    1

  • Dimensions (mm)

    213 x 239 x 67

  • Weight (kg)

    3.5

  • Official link

Related content

More components