Hifiverse

Headphones amplifiers - Bryston BHA-1

Description, images, technical data and specifications

Bryston BHA-1
Image source - (c) Bryston

The BHA-1 is a balanced headphone amplifier from Bryston of Canada, compatible with both single-ended and balanced headphones. Bryston describes it as functionally a miniature power amplifier. It is a purely analogue design with no digital inputs, and a pair of rear-mounted XLR outputs allows it to operate as an analogue preamplifier. It was released in 2012 at USD 1,395.

Key specs that matter

Power output is 2 W per channel into 32 ohms. THD+N is below 0.005% (20 Hz - 20 kHz, rated power), IM distortion is below 0.001% and signal-to-noise ratio is greater than 105 dB. Frequency response is 20 Hz - 20 kHz (±0.1 dB). Into a high-impedance load it delivers 20 V into 600 ohms (667 mW), and into a low-impedance load 4 V into 32 ohms (500 mW). Gain is selectable between 14 dB and 20 dB. Input impedance is 10 kohms unbalanced and +15 kohms/-5 kohms balanced. Dimensions are 432 or 483 x 69 x 282 mm (W x H x D), and weight is 5.3 kg.

Engineering and use context

Six fully discrete class A Bryston operational amplifiers are arranged in balanced dual mono circuitry. On the balanced outputs each headphone driver is powered by two amplifiers in balanced, or series, mode, for double the signal voltage. Bryston uses the same configuration in its 7B, 14B and 28B power amplifiers. Each half of a balanced output is driven by a separate amplifier in a bridged configuration, four output amplifiers in total, with no common ground.

Headphone outputs are a 4-pin XLR stereo jack, dual left/right 3-pin XLR jacks and a 6.35 mm stereo jack. All three are in parallel from the same output amplifiers. Its single-ended jack uses only one of the two output stages and delivers half the available power. Inputs are RCA, XLR and a 3.5 mm TRS mini jack, and all connectors are gold-plated. Volume is set by a laser-trimmed Noble potentiometer, and the balance control has a centre detent.

Cooling is by convection only, with the machined and anodised aluminium enclosure acting as the heat sink, so there are no fans. A Bryston internal analogue power supply is standard, and the optional external MPS-2 replaces it. A 12 V trigger input is on the rear panel. Options include a silver or black faceplate, a 17 or 19 inch faceplate and locking XLR connectors. Bryston gives a 10-year warranty.

Pairing

Bryston recommends a headphone load above 32 ohms, with 16 ohms as the minimum. Balanced headphones require a 4-pin XLR or dual 3-pin XLR cable. A source with balanced outputs connects to the XLR inputs.

Alternatives

Bryston has no other headphone amplifier in its range.

Specifications

  • Model name

    BHA-1

  • Maximum Power, 32 Ohms (mW RMS per channel)

    2000

  • Maximum Power, 50 Ohms (mW RMS per channel)

    N/A

  • Maximum Power, 300 Ohms (mW RMS per channel)

    N/A

  • Maximum Power, 600 Ohms (mW RMS per channel)

    N/A

  • Frequency response low +/- 3dB (Hz)

    20

  • Frequency response high +/- 3dB (Hz)

    20 000

  • Gain (dBu)

    N/A

  • THD (% at 1V RMS, 300 ohms)

    <0.005

  • Signal to Noise Ratio (dB)

    N/A

  • IMD (%, CCIR, 300 Ohms)

    N/A

  • Crosstalk (dB, 20Hz-20KHz, 300 Ohms)

    N/A

  • Output Impedance (Ohms)

    N/A

  • Dimensions (mm)

    432/483 x 69 x 282

  • Weight (kg)

    5.3

  • Official link