Hifiverse

Receivers - Emotiva BasX MR1

Description, images, technical data and specifications

Emotiva BasX MR1
Image source - (c) Emotiva

The BasX MR1 is an 11.2-channel Dolby Atmos and DTS:X cinema receiver from Emotiva. It has 11 channels of Class A/B amplification, a Soft Switch Class H power supply, an Analog Devices SHARC DSP and six HDMI 2.0b inputs. The amplifier section can be totally disabled, so the same chassis also works as a surround processor with 13.2 channels of line-level preamp outputs.

Key specs that matter

With all eleven channels driven, rated power is 100 W RMS per channel into 8 ohms and 130 W into 4 ohms at under 0.1% THD. Five channels driven give 135 W and 190 W, two channels 160 W and 260 W, and one channel 160 W into 8 ohms and 290 W into 4 ohms. Power bandwidth is 20 Hz - 20 kHz (+0/-0.15 dB), and broadband frequency response is 5 Hz - 80 kHz (+0/-3 dB). THD+N is below 0.005% (rated power, 1 kHz, 8 ohms), signal-to-noise exceeds 115 dB (A-weighted, referenced to rated power), and damping factor is above 500. Minimum load impedance is 4 ohms. The preamp outputs deliver 2 V RMS at below 0.0025% THD (1 kHz). Dimensions are 432 x 197 x 394 mm (W x H x D, without connectors), and net weight is 22.7 kg.

Engineering and use context

Emotiva describes the Soft Switch Class H supply as a design for high efficiency. Decoding covers Dolby Atmos, Dolby TrueHD, Dolby Surround, DTS:X, DTS-HD Master Audio and DTS, and upmixing is provided by the Dolby Surround Upmixer (DSU) and the DTS upmixer.

Each of the six HDMI inputs and two HDMI outputs supports 4K UHD with HDCP 2.2, HDR10, HDR10+ and Dolby Vision. According to Emotiva, the video switches route video from the selected input to the output without extraneous processing. ARC and eARC are supported on the primary output.

Audio inputs are four stereo analogue, two S/PDIF coaxial, two Toslink, a USB Audio (DAC) input and an internal Bluetooth receiver with aptX and a rear-panel antenna. Besides the eleven speaker outputs there are two balanced subwoofer outputs in parallel with the main subwoofer outputs. For system control the rear panel carries an IR input, an RS-232 port and a programmable trigger output, and a separate USB port is reserved for firmware updates. Mains voltage of 115 or 230 V is detected automatically.

Pairing

Speakers of 4 ohms nominal or higher are required. Through the preamp outputs, external power amplifiers can be added for some or all channels. Two subwoofers can be connected over balanced or unbalanced outputs.

Alternatives

The BasX MR1L is the smaller Emotiva cinema receiver with fewer amplified channels.

Specifications

  • Model name

    BasX MR1

  • Type

    AV Reciever

  • Number of main channels

    11

  • Number of subwoofers channels

    2

  • Decoding up to Dolby Atmos

    Yes

  • Decoding up to DTS X

    Yes

  • DSP chip

    N/A

  • Phono

    N/A

  • Output power (8Ω)

    100

  • Output power (4Ω)

    130

  • Frequency response low +/- 3dB (Hz)

    20

  • Frequency response high +/- 3dB (Hz)

    20 000

  • Signal to Noise Ratio (dB)

    >100

  • Total Harmonic Distortion + Noise (%)

    0.05

  • Damping factor

    >500

  • Dimensions (mm)

    N/A

  • Weight (kg)

    N/A

  • Official link

More components