Hifiverse

Preamplifiers — Extraudio XP5 MKII

Description, images, technical data and specifications

Extraudio XP5 MKII
Image source - (c) Extraudio

The XP5 MKII is a tube line preamplifier in the Origin line of Extraudio, a company that designs and engineers its products in the Netherlands. Extraudio calls it its definitive line preamplifier and the result of 14 years of research and development. Compared with the first XP5, the MKII version brings 21 changes, among them a revised input impedance and circuit topology, more power supply capacitance, shorter audio tracks, a 128-step volume control and longer remote battery life through new firmware.

Key specs that matter

Two 6922/ECC88 dual triodes are used in the pure class A voltage-gain and cathode-follower stages. Voltage gain is 11 dB nominal, RCA to RCA and XLR to XLR. Frequency response is 20 Hz - 20 kHz (±0.05 dB) and 1 Hz - 1 MHz (±1 dB). THD is below 0.003% (1 kHz, 2 Vrms output), signal-to-noise ratio is 100 dB(A), dynamic range is 102 dB(A) and channel separation is 88 dB at 1 kHz. Input impedance is approx. 82 kohms on RCA and 40 kohms differential on XLR, and output impedance is approx. 50 ohms at 1 kHz. Maximum output is 8 Vrms on RCA and 16 Vrms differential on XLR. The chassis measures 44 x 12 x 40 cm (W x H x D) and weighs 15 kg.

Engineering and use context

Each input is switched by a dedicated audio relay into a single tube gain stage in pure class A. The RCA output is a tube cathode-follower, and the XLR output is actively buffered and electronically balanced. Volume is set after the gain circuit by a motorised ALPS Blue Beauty logarithmic potentiometer with 128 microcontroller-managed positions.

Its high-voltage B+ supply is regulated, with multi-stage filtering through parallel reservoir capacitors and polypropylene bypassing, and the tube heaters run on DC. All analogue parts are powered from a sand-core transformer in a double dual-mono layout, while digital and control circuits have a separate isolated transformer. Symmetrical C0G/NP0 RF filtering on the inputs, a buffer protection circuit and an EMI and RF filter on the AC input are included. Printed circuit boards are 4-layer and electrolytic gold plated, and the chassis is 6061 aluminium.

The front panel has a power button, an optical rotary input selector with six input LEDs and a volume knob, with no display. Remote control is by the RC2, which has an internal battery charged from a standard USB charger.

Pairing

Inputs are four RCA line, one balanced XLR and a processor or home theatre bypass in RCA and XLR form. The RCA and XLR outputs work independently, for two power amplifiers or a stereo amplifier plus two subwoofers. Recommended load is 20 kohms or higher on RCA and 10 kohms or higher on XLR. The matching power amplifier is the XP-A1500.

Alternatives

The XP3 is an earlier, now discontinued Extraudio preamplifier.

Specifications

  • Model name

    XP5 MKII

  • Analog inputs (balanced)

    1

  • Analog inputs (single-ended)

    4

  • Analog outputs (balanced)

    1

  • Analog outputs (single-ended)

    1

  • Gain (dBu)

    N/A

  • Input sensitivity (mV)

    N/A

  • Output voltage (V)

    N/A

  • Input impedance (balanced) (Ω)

    40 000

  • Input impedance (single-ended) (Ω)

    82 000

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Maximum output level (balanced) (dBu)

    16 Vrms

  • Maximum output level (single-ended) (dBu)

    8 Vrms

  • Volume control range (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    10

  • Frequency response high +/- 3dB (Hz)

    250 000

  • Signal to Noise Ratio (SNR, unweighted) (dB)

    100

  • Total Harmonic Distortion + Noise (THD+N) (%)

    <0.003

  • Dimensions (mm)

    440 x 120 x 400

  • Weight (kg)

    15

  • Official link