Hifiverse

Preamplifiers - Schiit Audio KARA F

Description, images, technical data and specifications

Schiit Audio KARA F
Image source - (c) Schiit Audio

Kara F is the version of the Kara preamplifier from Schiit Audio that comes with the Forkbeard control system, listed at USD 799, or USD 50 less without the Forkbeard module, with the IR remote standard either way. Schiit describes it as a Nexus balanced preamp and headphone amp, fully discrete and solid state. Compared with the earlier Freya S, the rails are ±32 V instead of ±17 V, the transformer is rated 48 VA instead of 24 VA, and a headphone jack is added. Chassis and transformers are made in California, PCBs in California or Nevada, and assembly is in San Antonio, Texas, under a 5-year limited warranty.

Key specs that matter

Inputs are 2 XLR pairs and 3 RCA pairs, and outputs are 1 XLR pair and 2 RCA pairs, selectable from the front panel or by remote. Input impedance is 10 kohms, and output impedance is 75 ohms single-ended and 600 ohms balanced. Balanced to balanced at a gain of 1 (0 dB), THD and CCIR IMD are below 0.0002% (20 Hz - 20 kHz, 4 V RMS) and SNR exceeds 129 dB (A-weighted, ref. 4 V RMS), with response of 20 Hz - 20 kHz (-0.1 dB) and 3 Hz - 500 kHz (-3 dB). At a gain of 4 (12 dB) the figures are 0.0004% and 123 dB. Crosstalk is above 110 dB typical in all modes, and passive-mode THD+N is below the capability of an APx555 analyzer. The headphone output gives 1 W RMS per channel into both 32 and 300 ohms, with 0.25 ohm output impedance. Size is 406 x 203 x 51 mm, weight 5.0 kg and typical consumption 22 W.

Engineering and use context

Nexus is a current-feedback topology with nested differential stages. It is differential in and out and converts single-ended inputs to balanced. One 48 VA transformer supplies dual series regulated ±32 V rails with Schiit's Quietude topology, plus a regulated 5 VDC rail for the microprocessor. With these rails the balanced output can swing close to 100 V. Volume is set by a relay-switched stepped attenuator with discrete thin-film resistors in 128 steps of 0.625 dB, and Schiit states that channel matching holds down to the lowest level. The attenuator can also run fully passive, with no gain stage in the path. For the headphone output Kara F uses the same discrete gain stage as the single-ended line outputs, with headphone detection and fault sensing. Forkbeard controls volume, inputs and output modes across several Schiit products and stacks and adds system health alerts. Schiit describes the case as shelf- and rack-friendly.

Pairing

The XLR output connects to a power amplifier with balanced inputs. Schiit also positions Kara F as a remote volume control for its DACs. In passive mode there is no single-ended to balanced conversion.

Alternatives

The Schiit Freya 2 is a Fusion preamplifier that switches between tube and solid-state gain.

Specifications

  • Model name

    KARA F

  • Analog inputs (balanced)

    2

  • Analog inputs (single-ended)

    3

  • Analog outputs (balanced)

    1

  • Analog outputs (single-ended)

    2

  • Gain (dBu)

    N/A

  • Input sensitivity (mV)

    N/A

  • Output voltage (V)

    N/A

  • Input impedance (balanced) (Ω)

    10 000

  • Input impedance (single-ended) (Ω)

    10 000

  • Output impedance (balanced) (Ω)

    600

  • Output impedance (single-ended) (Ω)

    75

  • Maximum output level (balanced) (dBu)

    N/A

  • Maximum output level (single-ended) (dBu)

    N/A

  • Volume control range (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    20

  • Frequency response high +/- 3dB (Hz)

    20 000

  • Signal to Noise Ratio (SNR, unweighted) (dB)

    >129

  • Total Harmonic Distortion + Noise (THD+N) (%)

    <0.0002

  • Dimensions (mm)

    406 x 203 x 51

  • Weight (kg)

    5

  • Official link