Hifiverse

Preamplifiers - CAAS Elysian Pre-amplifier

Description, images, technical data and specifications

CAAS Elysian Pre-amplifier
Image source - (c) CAAS

The Elysian Pre-amplifier, or EPre, is a balanced line preamplifier from CAAS Audio, the Yorkshire company founded in 2006 by the brothers Carl and Neil Broomfield. Dr Carl Broomfield designed the hardware and Neil Broomfield wrote the software and firmware. It is a single-chassis dual mono design in the Elysian series alongside the Elysian 100 mono-block power amplifiers, and in 2018 it was listed at GBP 7,200.

Key specs that matter

Inputs are three pairs of XLR and two pairs of RCA, and outputs are one variable XLR pair and one variable RCA pair. Gain is 0 dB to -64 dB and mute in 128 steps of 0.5 dB for RCA-to-RCA and XLR-to-XLR, and +6 dB to -58 dB for RCA-to-XLR. Input impedance is 33 kohms, output impedance 60 ohms (RCA, and per phase on XLR). Maximum input and output level is 4 V RMS per phase. Frequency response is below 1 Hz to above 200 kHz (-3 dB), DC coupled, and 20 Hz - 20 kHz (±0.1 dB). THD is below 0.01% at 1 kHz (0 dB level, 2 V RMS), crosstalk below -90 dB, output SNR about 100 dB (A-weighted) and output DC offset below ±1 mV. Its case measures 350 x 330 x 80 mm (W x D x H) and weighs 8.6 kg.

Engineering and use context

CAAS machines the case from a single piece of aluminium, anodised silver or black. Separate toroidal transformers, three of 15 VA each, serve the left analogue, right analogue and digital sections behind a mains filter. Twelve discrete regulated supplies power the analogue channels and seven more the digital control circuits.

Inside are six zero feedback, class A amplifier modules, three per channel. Firmware-controlled relays select the module that gives the most direct signal path for each input and output configuration. In RCA-to-RCA or XLR-to-XLR mode that path is only the volume control and a JFET buffer, single for RCA and in parallel for balanced use. Volume is a 128-step relay switched control with silver contact relays and fixed precision metal film resistors. Every analogue section is DC coupled from input to output with no capacitors, and an ultra low frequency DC servo called NIDS keeps DC levels low. Power draw is below 20 W idle and 0.5 W in standby. A solid aluminium remote covers volume, input select and mute.

Pairing

Sources with low output DC offset are required. The matching CAAS power amplifiers are the Elysian 100 mono-blocks, switched through the CAAS Link 12 V trigger, and the matching source is the Digital Audio Streamer. There is no ground lift switch.

Alternatives

The CAAS Elysian Pre-amplifier II is the later preamplifier in the same series, with a BJT amplifier stage.

Specifications

  • Model name

    Elysian Pre-amplifier

  • Analog inputs (balanced)

    3

  • Analog inputs (single-ended)

    2

  • Analog outputs (balanced)

    1

  • Analog outputs (single-ended)

    1

  • Gain (dBu)

    64 (XLR-to-XLR), 58 (RCA-to-XLR), 64 (RCA-to-RCA)

  • Input sensitivity (mV)

    N/A

  • Output voltage (V)

    N/A

  • Input impedance (balanced) (Ω)

    33 000

  • Input impedance (single-ended) (Ω)

    33 000

  • Output impedance (balanced) (Ω)

    60

  • Output impedance (single-ended) (Ω)

    60

  • Maximum output level (balanced) (dBu)

    4

  • Maximum output level (single-ended) (dBu)

    4

  • Volume control range (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    1

  • Frequency response high +/- 3dB (Hz)

    200 000

  • Signal to Noise Ratio (SNR, unweighted) (dB)

    100

  • Total Harmonic Distortion + Noise (THD+N) (%)

    < 0.01

  • Dimensions (mm)

    350 x 330 x 80

  • Weight (kg)

    8.6

  • Official link