Hifiverse

Preamplifiers - ToneWinner AD-1PRE+

Description, images, technical data and specifications

ToneWinner AD-1PRE+
Image source - (c) ToneWinner

The AD-1PRE+ is a two-channel stereo preamplifier from Guangzhou Tonewinner Electronics, sold under the Tone Winner name. It combines digital decoding, analogue source switching and an MM/MC phono stage in one aluminium chassis, and Tonewinner describes it as its latest flagship decoding preamplifier. It has no speaker-level amplification and is listed by Tonewinner in a configuration with the AD-1PA+ power amplifier, the TY-1CD player and TD-8 speakers.

Key specs that matter

Conversion uses an ESS ES9038Q2M DAC chip. Over USB it accepts DSD64 to DSD512, DoP64 to DoP256 and PCM up to 32 bit/768 kHz. Coaxial and optical inputs take PCM at 44.1-192 kHz and DoP64. Digital inputs are two optical, two coaxial and one USB. Analogue inputs are two unbalanced line inputs (CD and AUX), one balanced XLR input and separate MM and MC phono inputs. Outputs are two unbalanced RCA pairs and one balanced XLR pair, plus a 12 V trigger output. Tonewinner quotes THD of 0.0003% or less (1 kHz), S/N of at least 120 dB (A-weighted), frequency range of 10 Hz - 180 kHz (+1/-3 dB) and crosstalk of at least 102 dB (1 kHz). Dimensions are 444 x 120 x 413 mm (W x H x D), with a net weight of 9.7 kg and a gross weight of 12.6 kg.

Engineering and use context

A CS8416 chip is the digital receiver, and a CT7601PR chip is the USB interface. In the I/V stage the AD-1PRE+ uses OPA1632 fully differential operational amplifiers, while OPA1612 bipolar op amps, rated at 1.1 nV/√Hz noise density, form the balanced-to-unbalanced circuit. In total there are five OPA1612, four OPA1632 and one OPA1642. Volume is set by a JRC MUSES72323 electronic volume chip.

Inside, separate chambers isolate the circuit sections from mutual interference, and the analogue circuits run from a dedicated audio power supply. Tonewinner's wide-voltage design works on AC 110 V and AC 220 V, and standby consumption is 1 W or less. Its all-aluminium alloy enclosure has an anodised, brushed finish. Files played over USB include DSF, DFF, ISO, FLAC, ALAC, AIFF, APE, WAV, OGG, MP3 and WMA, and a phone connects through an OTG adapter. The aluminium remote control selects every input, and its DIM key sets display brightness. Supplied accessories are the remote, a power cord, an optical cable, a signal cable, the manual and a certificate.

Pairing

A separate power amplifier is required. The matching power amplifier is the AD-1PA+, connected over the XLR output. Turntables with MM or MC cartridges connect to the phono inputs, and the trigger output connects to amplifiers with a 12 V trigger input.

Alternatives

Tone Winner has no other model in the preamplifier category.

Specifications

  • Model name

    AD-1PRE+

  • Analog inputs (balanced)

    1

  • Analog inputs (single-ended)

    4 RCA (2 Phono MM/MC)

  • Analog outputs (balanced)

    1

  • Analog outputs (single-ended)

    2

  • Gain (dBu)

    N/A

  • Input sensitivity (mV)

    N/A

  • Output voltage (V)

    N/A

  • Input impedance (balanced) (Ω)

    N/A

  • Input impedance (single-ended) (Ω)

    N/A

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Maximum output level (balanced) (dBu)

    N/A

  • Maximum output level (single-ended) (dBu)

    N/A

  • Volume control range (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    10

  • Frequency response high +/- 3dB (Hz)

    180 000

  • Signal to Noise Ratio (SNR, unweighted) (dB)

    >=120 (A-weighted)

  • Total Harmonic Distortion + Noise (THD+N) (%)

    <=0.0003

  • Dimensions (mm)

    444 X 106 X 424

  • Weight (kg)

    9.7

  • Official link