Hifiverse

Preamplifiers - Soulution Audio 525 preamplifier

Description, images, technical data and specifications

Soulution Audio 525 preamplifier
Image source - (c) Soulution Audio

The 525 is a line preamplifier in soulution's 5 Series, made by Spemot AG in Dulliken, Switzerland. soulution states that it owes much to the design of the range-topping 725 Preamplifier and uses the same volume control.

Key specs that matter

Inputs are 2 x balanced (XLR) and 2 x unbalanced (RCA), with an input impedance of 820 kohms on XLR and 47 kohms on RCA. Outputs are 1 x balanced (XLR) and 1 x unbalanced (RCA), both with an output impedance of 10 ohms. Maximum output voltage is 16 V RMS balanced and 8 V RMS unbalanced, and maximum output current is 0.2 A (limited). Frequency response is 0 - 2 MHz (-3 dB), THD+N is below 0.00009% (20 Hz - 20 kHz), signal-to-noise ratio is 120 dB and channel separation is 130 dB at 1 kHz. Maximum gain is +15 dB, and the volume control range is +15 dB to -79 dB in 1 dB steps. Power consumption is 25 W in operation and below 0.5 W in standby. The chassis measures 442 x 143 x 448 mm (W x H x D) and weighs approx. 20 kg.

Engineering and use context

Vishay Dale resistors and relays form the volume control. During a level change a parallel Programmable Gain Amplifier (PGA) path is active, and the signal path then switches back to the resistor network. Input selection uses relays that switch ground as well as signal connections, so only the selected input is connected to the electronics. All signals are buffered immediately after the input, and the balanced input stage is optimised for low residual noise and common mode rejection.

Construction is dual-mono with an unbalanced circuit concept. The analogue circuits and power supplies of the two channels are physically separated and decoupled with filter networks, and the audio section is separated from the digital circuits. A switched-mode power supply with low-noise linear regulators and more than 400,000 µF of storage powers the 525. Its fast output stage is designed to drive long cables. A 12 V LINK control signal provides remote turn-on.

Pairing

The balanced and unbalanced outputs connect to power amplifiers with XLR or RCA inputs. Through the LINK connection, other soulution components switch on with the 525.

Alternatives

The 727 is soulution's 7 Series preamplifier.

Specifications

  • Model name

    525 preamplifier

  • Analog inputs (balanced)

    2

  • Analog inputs (single-ended)

    2

  • Analog outputs (balanced)

    1

  • Analog outputs (single-ended)

    1

  • Gain (dBu)

    15

  • Input sensitivity (mV)

    N/A

  • Output voltage (V)

    N/A

  • Input impedance (balanced) (Ω)

    820 000

  • Input impedance (single-ended) (Ω)

    47 000

  • Output impedance (balanced) (Ω)

    10

  • Output impedance (single-ended) (Ω)

    10

  • Maximum output level (balanced) (dBu)

    16

  • Maximum output level (single-ended) (dBu)

    8

  • Volume control range (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    0

  • Frequency response high +/- 3dB (Hz)

    2 000 000

  • Signal to Noise Ratio (SNR, unweighted) (dB)

    120

  • Total Harmonic Distortion + Noise (THD+N) (%)

    < 0.00009

  • Dimensions (mm)

    442 × 143 × 448

  • Weight (kg)

    20

  • Official link

Related content