Hifiverse

Power amplifiers stereo - Cary Audio SA-200.2 ES

Description, images, technical data and specifications

Cary Audio SA-200.2 ES
Image source - (c) Cary Audio

The SA-200.2 ES is a two-channel solid-state power amplifier from Cary Audio, released in April 2018 at USD 4,495 and designed and built at the Cary factory in North Carolina. It is the next generation of the SA-200.2, with a modular approach that Cary chose for consistent performance, ease of manufacture and serviceability. In bridged form the same design becomes the SA-500.1 ES monoblock. Cary intends both for music systems and for home cinema.

Key specs that matter

Circuit type is solid state, class A/B. Output is 2 x 200 W into 8 ohms and 2 x 350 W into 4 ohms, rated from 20 Hz to 20 kHz. Frequency response is 10 Hz - 50 kHz (±0.1 dB). Voltage gain is 28 dB, with 22 kohms input impedance on RCA and XLR. Signal-to-noise ratio is above 100 dB (A-weighted), THD stays below 0.05% at rated output and damping factor exceeds 400 from 10 Hz to 20 kHz. Cary quotes very high current capability, stability into low impedance loads and 3 dB of dynamic headroom. Inputs are two RCA and two XLR jacks, and outputs are two pairs of heavy-duty, gold-plated binding posts. Its remote trigger accepts 3.3 - 24 V DC at 5 mA or greater. Mains supply is 117/234 V AC at 50-60 Hz. Dimensions are 191 x 450 x 495 mm (H x W x D), and weight is 29.5 kg.

Engineering and use context

Inside is a custom 850 VA low-noise toroidal transformer with separate windings for the regulated input board. Capacitance exceeds 57,000 µF per channel. Cary mounts these power supply capacitors on the amplifier boards and adds bypass capacitors at the output devices, using multiple smaller capacitors because large ones have higher ESR. Each chassis carries sixteen high-current 150 W bipolar output devices with matched output transistors. A new heat sink with a larger radiating surface and fin structure raises heat dissipating capability by as much as 50% over previous designs.

At the front end sits a monolithic device on a custom heat sink, with short circuit board traces and a ground plane around sensitive components. High-precision metal film resistors are used in almost all circuitry. Four easily replaceable fibreglass printed circuit boards hold the electronics, and each module is a self-contained unit, replaced after removing the top cover. Thermal and DC-offset protection uses a high-current relay that disconnects the speakers, and Cary does not use traditional voltage and current limiting. Break-in time is 100 hours. Finish is a black epoxy-coated steel chassis with a silver anodised aluminium faceplate, black optional.

Pairing

A preamplifier with balanced XLR or single-ended RCA outputs is required. A preamplifier with a DC trigger output can switch it on remotely.

Alternatives

The CAD-120S MkII is Cary Audio's stereo tube power amplifier.

Specifications

  • Model name

    SA-200.2 ES

  • Input sensitivity (mV)

    N/A

  • Input impedance (balanced) (Ω)

    22 000

  • Input impedance (single-ended) (Ω)

    22 000

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    2 x 200

  • Output power (4Ω) (W)

    2 x 350

  • Gain (dBu)

    28

  • Frequency response low +/- 3dB (Hz)

    10

  • Frequency response high +/- 3dB (Hz)

    50 000

  • Signal to Noise Ratio (dB)

    N/A

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    N/A

  • Max power consumption (W)

    N/A

  • Damping factor

    N/A

  • Dimensions (mm)

    197 × 450 × 495

  • Weight (kg)

    29.5

  • Official link

More components