Hifiverse

Power amplifiers stereo - Mark Levinson № 632

Description, images, technical data and specifications

Mark Levinson № 632
Image source - (c) Mark Levinson

The № 632 is the stereo power amplifier of the Mark Levinson 600 Series - a fully differential, fully discrete, dual-monaural design. It was shown at High End Munich 2025 together with the № 631 monoblock and the № 626 preamplifier. Mark Levinson, founded in the United States in 1972 and now part of Harman, set the price at USD 30,000 or GBP 29,999, with shipments scheduled for the fourth quarter of 2025.

Key specs that matter

Rated output is 250 W RMS per channel into 8 ohms (20 Hz - 20 kHz, below 0.3% THD), doubling into 4 ohms, with stability into 2 ohms. Frequency response is 10 Hz - 50 kHz (±0.2 dB) and 10 Hz - 200 kHz (+0.2/-1.5 dB). Signal-to-noise ratio is above 94 dB (ref. 2.83 V RMS). Input impedance is 900 kohm balanced and 450 kohm unbalanced, voltage gain is 26 dB, and input sensitivity is 142 mV for 2.83 V output. Inputs are two XLR and two RCA, and outputs are four pairs of Hurricane binding posts, two pairs per channel. Idle consumption is below 250 W. Dimensions are 202.7 x 455.0 x 522.6 mm (H x W x D), and weight is 47.2 kg.

Engineering and use context

Each channel has twelve discrete 15 A, 260 V, 200 W bipolar output transistors in TO-264 cases, and each one is driven by a dedicated 230 V, 70 MHz TO-126 driver transistor. Operation is Class A/AB. Voltage gain and driver stages run in Class A, as do the input and current transfer stages. Its input stage uses matched JFETs in a cascode configuration, followed by a folded cascode and current mirror on bipolar devices. No capacitors sit in the direct-coupled signal path. According to Mark Levinson, high open-loop linearity and unusually high bias current allow minimal feedback.

A custom low-noise 1,900 VA toroidal transformer with separate secondary windings for each output stage is centrally located and structurally isolated. Discrete Schottky rectifiers and 80,000 µF of filter capacitance in total complete the power supply. Inside, a modular architecture separates low-level circuitry from the power supply, with critical components on rubber isolators, and mechanically isolated foot bars decouple the chassis from its surroundings. Aluminium and steel are anodised black on a silver plinth, with heat sink side panels, a vented top and red accent lighting behind glass. In Eco Mode the amplifier enters standby after 20 minutes without signal.

Pairing

The matching preamplifier is the № 626. A rear switch selects the XLR or RCA input, and Mark Levinson recommends the balanced connection. The terminals allow single-wiring or bi-wiring.

Alternatives

The Mark Levinson № 534 is an earlier dual-monaural stereo power amplifier.

Specifications

  • Model name

    № 632

  • Input sensitivity (mV)

    N/A

  • Input impedance (balanced) (Ω)

    N/A

  • Input impedance (single-ended) (Ω)

    N/A

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    N/A

  • Output power (4Ω) (W)

    N/A

  • Gain (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    N/A

  • Frequency response high +/- 3dB (Hz)

    N/A

  • Signal to Noise Ratio (dB)

    N/A

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    N/A

  • Max power consumption (W)

    N/A

  • Damping factor

    N/A

  • Dimensions (mm)

    202.7 x 455.0 x 522.6

  • Weight (kg)

    N/A

  • Official link

More components