Hifiverse

Power amplifiers stereo - Audio Analogue AA100DM

Description, images, technical data and specifications

Audio Analogue AA100DM
Image source - (c) Audio Analogue

The AA100DM is a stereo power amplifier and the latest addition to the PureAA line of Audio Analogue, the Italian brand designed and produced by AF Group Srl in Monsummano Terme. Its amplifier stage is derived from the one in the Puccini Anniversary integrated amplifier, with output power increased to 100 W. Two units can be configured as a bridge-mono pair.

Key specs that matter

Output power with one channel operating is 100 W into 8 ohms, 200 W into 4 ohms and 320 W into 2 ohms, all at 1% THD. In bridge-mono the figures are 400 W into 8 ohms and 700 W into 4 ohms. Each channel has one RCA and one XLR input, input impedance is 47 kOhm and gain is 26 dB. Sensitivity is 1.4 V RMS (100 W into 8 ohms). Bandwidth is 95 kHz (-3 dB), output resistance is 0.25 ohm (nominal power into 8 ohms, 1 kHz), input noise is about 3 µV (A-weighted) and SNR is above 110 dB (A-weighted). Standby consumption is 0.5 W. Dimensions are 120 x 445 x 390 mm (H x W x D), and weight is 15.5 kg.

Engineering and use context

Audio Analogue describes the AA100DM as a fully balanced power amplifier with no global feedback, built in dual-mono with discrete components. According to the company, the feedback-free power stage is less sensitive to the load, with no tendency to oscillate, no high-frequency resonance peaks and no saturation in the input stage. A 760 VA transformer supplies both channels, and the output stage uses six pairs of On Semiconductor power transistors, three pairs per channel.

Oversized military-grade through-hole resistors are chosen to minimise thermally induced distortion, alongside polypropylene capacitors. Internal wiring is pure solid 7N OCC copper, and the output connectors are gold-plated. A microcontroller manages the unit. On the rear panel sit a 5-12 V trigger input, an IEC 10 A inlet with fuse holders and a power switch. If a fault is sensed, the amplifier turns off at once, and the blink count of the front LED ring identifies overheating, DC on a channel, or overcurrent and short circuit. Bridge-mono use requires a dedicated kit with a quick guide, sold separately with the second unit. Finishes are natural aluminium and satin black.

Pairing

A preamplifier with balanced XLR or RCA outputs is required. When the RCA inputs are used, pins 1 and 3 of the XLR sockets stay bridged as supplied. A preamplifier with a 5-12 V trigger output can switch the AA100DM on.

Alternatives

The Audio Analogue Donizetti Anniversary is a higher-powered stereo power amplifier from the brand, rated at 250 W into 8 ohms.

Specifications

  • Model name

    AA100DM

  • Input sensitivity (mV)

    N/A

  • Input impedance (balanced) (Ω)

    47 000

  • Input impedance (single-ended) (Ω)

    47 000

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    100

  • Output power (4Ω) (W)

    200

  • Gain (dBu)

    26

  • Frequency response low +/- 3dB (Hz)

    1

  • Frequency response high +/- 3dB (Hz)

    90 000

  • Signal to Noise Ratio (dB)

    >100

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    <0,1

  • Max power consumption (W)

    N/A

  • Damping factor

    N/A

  • Dimensions (mm)

    435 × 130 × 390

  • Weight (kg)

    15.5

  • Official link

Related content