Hifiverse

Power amplifiers stereo — Linn Akurate 4200

Description, images, technical data and specifications

Linn Akurate 4200
Image source - (c) Linn

The Akurate 4200 is the four-channel model of Linn's Akurate power amplifier range, introduced in May 2007 alongside the two-channel 2200 and the three-channel 3200. Linn offers each model in a balanced XLR or an unbalanced RCA version, for stereo, multi-channel or multi-amp systems and for passive or Aktiv loudspeakers. The Australian list price of the current version is AUD 12,995.

Key specs that matter

Maximum output is 200 W rms into 4 ohms and 111 W rms into 8 ohms per channel, and Linn specifies the amplifier as unconditionally stable into all loudspeaker loads. Frequency response is 1.4 Hz - 41 kHz, harmonic distortion is below 0.01%, and peak output voltage is 41 V. Input impedance is 7.5 kohms (RCA) or 7.8 kohms (XLR), with clipping at 1.1 V rms and 2.2 V rms respectively. Gain is adjustable for Aktiv use, from 25.6 to 32.6 dB on the RCA model (default 28.6 dB) and from 19.6 to 26.6 dB on the XLR model (default 22.6 dB). Rated input power is 300 W. The current chassis measures 380 x 91 x 380 mm (W x H x D) and weighs 8.3 kg, against 381 x 80 x 355 mm and 6.7 kg for the original version. Finishes are silver or black.

Engineering and use context

Each channel uses Linn's patented Chakra amplifier topology, which combines a monolithic chip amplifier with bipolar transistors - the chip operates alone at low currents, and the bipolar transistors take over at higher levels. Linn credits Chakra with increased power, reliability and efficiency, less heat and lower distortion. The original version has Linn's 'silent power' switch mode power supply, and the current version uses the Linn Dynamik switch mode supply. Mains input is 100 - 120 V or 220 - 240 V AC at 50 - 60 Hz.

Every channel has its own input and line output for daisy-chaining further amplifiers. The eight binding posts accept 4 mm banana plugs and 6 mm or 8 mm spade connectors. Inside, the 4200 accommodates Linn Aktiv crossover cards and detects them automatically. Signal-sensing circuitry detects an audio signal and returns the amplifier to sleep mode when it is absent, while fault detection and protection circuits guard against short circuits and excessive loads.

Pairing

A preamplifier or source with RCA or balanced XLR outputs matching the chosen version is required. Four channels allow a pair of loudspeakers to be bi-amped, or one channel per drive unit in an Exakt or Aktiv system.

Alternatives

The Linn Akurate 2200 is the two-channel model of the same range, with the same 200 W into 4 ohms rating per channel.

Specifications

  • Model name

    Akurate 4200

  • Input sensitivity (mV)

    N/A

  • Input impedance (balanced) (Ω)

    N/A

  • Input impedance (single-ended) (Ω)

    N/A

  • Output impedance (balanced) (Ω)

    N/A

  • Output impedance (single-ended) (Ω)

    N/A

  • Max current (A)

    N/A

  • Output power (8Ω) (W)

    4 x 111

  • Output power (4Ω) (W)

    4 x 200

  • Gain (dBu)

    N/A

  • Frequency response low +/- 3dB (Hz)

    N/A

  • Frequency response high +/- 3dB (Hz)

    N/A

  • Signal to Noise Ratio (dB)

    N/A

  • Total Harmonic Distortion + Noise (0% global feedback) (%)

    N/A

  • Total Harmonic Distortion + Noise (100% global feedback) (%)

    N/A

  • Max power consumption (W)

    N/A

  • Damping factor

    N/A

  • Dimensions (mm)

    380 × 91 × 380

  • Weight (kg)

    8.3

  • Official link

More components